User Manual
Table Of Contents
- English
- Table of contents
- Introduction
- Panels
- Connect your instrument and turn on the power
- Playing programs
- Creating phrases
- Overdubbing a performance by playing along with a recorded phrase
- Applying the Loop Effect to a recorded phrase
- Specifying how the loop will stop
- Resampling
- Applying the limiter to the recorded phrases
- Erasing a loop-recorded phrase
- Loop status
- About the Pre Effect and the Loop Effect
- Control pedal settings
- Restoring the factory settings
- Auto Power-Off function
- Troubleshooting
- Block diagram
- Main specifications
- Français
- Sommaire
- Introduction
- Panneaux
- Connexion de l’instrument et mise sous tension
- Jouer avec des programmes
- Créer des phrases
- Ajout d’un nouvel enregistrement à une phrase
- Traiter une phrase enregistrée avec un effet de boucle
- Mode d’arrêt de la boucle
- Rééchantillonnage (Resampling)
- Traiter les phrases enregistrées avec le limiteur
- Effacer la phrase d’une boucle
- Etat de la boucle (Loop Status)
- Pré-effets et effets de boucle
- Réglages de la pédale d’expression
- Rétablir les réglages d’usine
- Coupure automatique d’alimentation
- Dépannage
- Schéma de principe
- Fiche technique
- Deutsch
- Inhaltsübersicht
- Vorweg
- Bedienelemente
- Anschließen des Instruments und einschalten
- Spielen von Programmen
- Aufzeichnen von Phrasen
- Ergänzen einer Phrase um weitere Parts
- Bearbeiten aufgezeichneter Phrasen mit dem Loop-Effekt
- Festlegen, wie die Schleife endet
- Resampling
- Bearbeiten aufgezeichneter Phrasen mit dem Limiter
- Löschen einer Loop-Phrase
- Loop-Status
- Über den Pre- und Loop-Effekt
- Einstellungen für das Expression-Pedal
- Laden der Werkseinstellungen
- Energiesparfunktion
- Fehlersuche
- Blockschaltbild
- Wichtigste technische Daten
33
About the Pre Effect and the Loop Effect
Loop Effects
When using a loop effect, it is particularly useful to assign a
loop effect parameter to the control pedal.
Vol: VOLUME
This effect lets you use the control pedal to control the
volume.
If you start resampling with this effect selected, the output
whose volume is controlled by this effect will be recorded on
the currently selected loop. You can also use this to combine
the outputs of the two loops into a single loop.
• EDIT knob: Specifies the sound(s) whose volume will be
controlled.
Cur: The volume of the loop that’s currently selected will
be controlled.
L1.2:The volume of Loop 1 and Loop 2 will be controlled.
ALL: The volume of the input sound, Loop 1, and Loop 2
will be controlled.
• Control pedal: Controls the volume of the sound(s)
specified by the EDIT knob.
FAd: X-FADE
This effect uses the control pedal to control the mix balance.
If you execute resampling with this effect selected, the mix
output controlled by the Loop Effect will be recorded into
the currently selected loop.
• EDIT knob: Specifies the sounds whose mix balance will
be controlled.
In.L:The pedal will control the mix balance between the
input and the loop that’s currently selected.
L1.2:The pedal will control the mix balance between Loop
1 and Loop 2.
• Control pedal: Controls the mix balance specified by the
EDIT knob.
rEV: REVERSE
This effect reverses the playback. Advancing the control
pedal will increase the mix amount of reverse playback. This
is particularly effective when used on audio that contains
continuous change, such as a guitar solo or vocal.
• EDIT knob: Selects what will happen when you switch
between forward and reverse playback.
FAd:Crossfade between forward playback and reverse
playback.
ALt: Switch alternately between forward playback and
reverse playback.
• Control pedal: Switches between forward playback and
reverse playback.
LIL: LOOP IN LOOP
When you advance the control pedal, this effect instantly
creates an even shorter phrase from the phrase that’s
currently playing. By controlling the length of the phrase,
you can also produce roll-like effects.
• EDIT knob: Specifies the time signature used when you
advance the control pedal while a phrase is playing back.