Product Description

©
2022 VoxxElectronics, All rights reserved.
NR6867T--2022-07-11
1
Product Description
The R
6867T control center is compatible with the following modules:
DS4 and DS4+.
Mounting the Control Center
Note
Once this replacement control center has been installed, all
remote controls must be paired with your system. See Remote
Pairing for details and follow the instructions for your remote
control type.
The control center’s position should be discussed with the vehicle owner
prior to installation since the antenna, with built-in status LED and Valet/
Program, must be visible/accessible to the customer.
The best position to locate the control center is centered high on the front
windshield. It can be mounted vertically or horizontally relative to the
windshield. Metallic window tint can also aect range negatively, so this
should be a consideration when determining the mounting location.
After you determine the best mounting location, follow these steps:
Clean the mounting area with a quality glass cleaner or alcohol to remove
any dirt or residue.
Plug the cable into the control center.
Mount the control center with double-sided tape.
Route the cable down the window pillar to the control module and plug
the cable in the control module.
CONTROL CENTER
CABLE
CONTROL
MODULE
Remote Pairing
Prepare the vehicle system to be Paired with a new remote
1. Open at least one vehicle door.
2. Turn the key to the ON position.
3. Within 5 seconds press and release the Control button on the Control
Center one time.
4. Within 5 seconds, press and hold the Control button on the Control
Center. The status LED begins flashing in single flash sequence and
the siren/horn sounds once to confirm the system is ready for remote
pairing. Release the button.
5. Locate your remote control model below and follow the instructions.
System Pairing will exit if:
• The ignition is turned o
• The open door is closed
• 60 seconds lapses with no actions
Note : Make sure the remote to be paired with the system is set for the de-
sired Car 1 or Car 2 operation.
LCD Remote Control:
1. Press and hold the
AUX
button for 8 seconds, the remote beeps once,
Main Menu
is displayed. Release the
AUX
button.
2. Press the AUX or
AUX
buttons until
Pair
is displayed.
3. Press and hold the
AUX
button until the remote beeps 3 times then re-
lease the
AUX
button. The remote is now ready to pair with the system.
4. Press the
AUX
button.
5. Wait several seconds for feedback as the remote generates a security
encryption and sends it to the Control Center. If pairing is successful
the siren/horn sounds and the remote emits several tones. The screen
displays if the Pairing is successful or failed with corresponding text. If
pairing fails repeat step 4.
To exit pairing mode on the remote:
• Press and release the
A U X
button.
• Wait 30 seconds without pressing a command button on the remote.
Responder LED or Companion Remote Control:
1. Press and hold the
AUX
button for 8 seconds. The transmit LED will come
on solid. Release the
AUX
button.
2. Press and hold the
AUX
until the transmit LED flashes 3 times then
comes on solid.
3. Press the
AUX
button.
4. Wait several seconds for feedback as the remote generates a security
encryption and sends it to the Control Center. If pairing is successful
the siren/horn sounds and the 2-way remote emits several tones (the
companion remote does not generate tones). If pairing is not suc-
cessful press and release the
AUX
button once and then repeat steps
2 and 3.
To exit pairing mode on the remote:
• Press and release the
AUX
button once, then press and hold until the
transmit LED shuts o.
• Wait 30 seconds without pressing a command button on the remote
control.
R6867T
Replacement
Digital Control Center