Introduction Thank you for purchasing your new Voyager lon E-Scooter and welcome to the Voyager family. We hope that you'll do plenty of exploring on your new scooter. The lon E-Scooter is compact, portable and packs plenty of power to get you where you're going. Please enjoy your new scooter responsibly and be sure to read the entire instruction manual before your first use. Have a blast, be safe and Get Moving SPECIFICATIONS * Top Speed: 12.5 mph * Power: 250W « Battery Range: 10 Miles * Weight: 19.
CAUTION As with any motorized vehicle, whenever you ride your lon E-Scooter you may risk death or serious injury from loss of control, collision or falls. All riders should read, understand and take heed of the instructions in the user guide when riding. BEFORE YOU RIDE Prior to use, perform a quick visual check fo verify that the scoffer in good shape and that your equipment is not damaged. Make sure the battery is fully charged before your first use.
THE ION E-SCOOTER Switch button Display Power/Front light Right handle bar Accelerator ~ Hook N S Brake ~ Left handle bar Front light Folding lat¢h Rear fender Hook hole— Charging Rear light Front fender Rear wheel Front wheel
ION DISPLAY Speed unit Front light Motor error Cruise control Accelerator err Brake emir Start Mode
Foundling ‘ 2. Open the molding latch 1. Push the \§H P safety latch f 4, Put the hook into the hook hole .
USING THE ION Power button function description: 1. Power on/off: Press and hold the red power button on the right side 1o power the scooter on. Press and hold the button again to tum it off. 2. Gear switch: Gear switch: Tap the eff red button to change gears. There are four gears: P1, P2, P3 and P4 3. Lighting: To tum the lights on or off, fap the power button quickly. Once for on, then again for off. 4, Settings: Press and hold both the left and right buttons fo infer settings mode.
USING THE ION Startup Modes Explained: When in the settings menu, on option CZ, you can adjust the start mode on the lon, bestselling between slide start and zero start. Slide start requires the scooter to already be in motion before the thirtieth will work. in this mode the scanter will not move forward from a complete stop. and requires the rider to initially push the scooter into motion. Slide start mode helps your scooter conserve power and can prolong battery life.
SAFE RIDING 1. Do not lean foo hoed when accelerating or decelerating. and do nof put moats of your body weight over the handlebars. 2. Ride in o stoning position and esp one foot in front of the other. 3, Neap the handlebar in line with your body when muting and be sure o look ahead before you hymn. 4.
CHARGING 1} Ensure that the scooter s charging in o clean and dry environment, the input voltage is guarani between 110v-240v and that the charging cable is connected properly. The red eight indicates the scooter is being charged. 2} When the fight fums green, charging is completed. 3} Don't tum on the scooter suing charging for your safety, 4) Disconnect the scooter from the charger when the charging is complete.
TROUBLESHOOTING 1. The display is working but the motor is not working a. The motor is damaged If the front whee! doesn’t tum and the motor is not running, check to see if the scooter feels hot. There may be a short circuit, and the scooter should immediately be powered off. b. The scooter has been exposed to excessive moisture Moisture getting inside the scooter can also cause damage and short circuiting.
FCC COMPLIANCE Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: {1) this device may not cause harmful interference, and (2} this device must accept any interference received, including interference that may cause undesired operation.
WARRANTY This warranty covers the original consumer purchaser only and is not transferable. This warranty covers products that fail to function property UNDER NORMAL USAGE, due to defects in material or workmanship. Your product will be repaired or replaced at no charge for parts or labor for a period of one year.
