User Manual

ManualsBrandsVQ Model ManualsAircraftsCurtiss P-40

Table Of Contents

RADIO CONTROL MODEL

INSTRUCTION MANUAL / MONTAGEANLEITUNG

CURTISS P-40

VQAO20U / VQA021F / VQA0201B / VA022C

SPECIFICATIONS

Wingspan 1570mm

Length 1360mm

Electric Motor 870 Watt Brushless Motor

Glow Engine .60 2-T / .90 4-T

Radio 6 Channel / 7 Servos

TECHNISCHE DATEN

Spannweiter 1570mm

Lange 1360mm

Elektroantrieb 870 Watt Brushless Motor

Verbrennerantrieb 10cc 2-T / 15cc 4-T

Fernsteuerung 6 Kanal / 7 Servos

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Summary of content (11 pages)

PAGE 1
RADIO CONTROL MODEL CURTISS P-40 VQAO20U / VQA021F / VQA0201B / VA022C INSTRUCTION MANUAL / MONTAGEANLEITUNG TECHNISCHE DATEN SPECIFICATIONS Spannweiter 1570mm Lange 1360mm Elektroantrieb 870 Watt Brushless Motor Verbrennerantrieb 10cc 2-T / 15cc 4-T Fernsteuerung 6 Kanal / 7 Servos Wingspan Length Electric Motor Glow Engine Radio 1570mm 1360mm 870 Watt Brushless Motor .60 2-T / .90 4-T 6 Channel / 7 Servos WARNING! This radio controlled model is NOT a toy.
PAGE 2
REQUIRED FOR OPERATION (Purchase separately) BENOTIGTE KOMPONENTEN FUR DEN ABFLUG (Nicht enthalten) 12x6 for .60 - 2 cycle engine 13x7 for .90 - 4 cycle engine 14X8 for Quantum 4120/07 BOOTS 60 Phoenix-60 Brushless Motor Control or equivalent. Extension for aileron Flap and retract servo. Retract landing gear VQAR07 Retract servo x1 Minimum 6 channel radio for airplane with 7 servos (Motor control x1) .Aileron x2 .Elevator x1 .Rudder x1 .Flap x 2 .60 - 2 cycle Brushless Motor BOOST 60 .
PAGE 3
1- Joining the wing / Flachenverbindung TOP VIEW / AUFSICHT A B A B 1- Using a pencil, mark the center of the brace. 2- Trial fit the wing joiner into one of the wing panels. It should insert smoothly up to the center line marked above. 3- Slide the other wing half onto the dihedral brace until the wing panel meet. If the fit is over tight, it may be necessary to lightly sand the dihedral brace. 4- Check for the correct dihedral angle.
PAGE 4
- WING - BOTTOM VIEW UNTERSICHT Retract landing gear / Einziehfahrwerk VQ-AR07 - 160227 (Purchase separately) X X Retract servo 1/8x15/32” (3x12mm) screw Pillow ball E-ring STEP 1 STEP 2 STEP 3 RETRACT LANDING GEAR INSTALLATION 5- Fixed gear / Starres Fahrwerk WING - BOTTOM VIEW UNTERSICHT Main gear (left) Plastic strapX4 Main gear (right) Gear mount x 2 Ply gear mount plate x 2 3x12mm screw 3x12mm screw. ......
PAGE 5
7- ABS Shield WING - BOTTOM VIEW UNTERSICHT CA R “R” for the right half wing “L” for the left half wing CA 8- Flap, Aileron servo / Flap, querruder servo WING - BOTTOM VIEW / UNTERSICHT Aileron extension cord Aileron extension cord exit X Aileron servo hatch flap extension cord Flap servo hatch Aileron servo installation Aileron servo hatch 2x10mm Servo mount 2x10mm Flap servo hatch Servo mount 1.5mm 1.
PAGE 6
9- 1-Trial fit the horizontal stabilizer into the fuselage. Use a pencil to carefully trace around the top and bottom of the horizontal stabilizer where it meets the fuselage. 2-Remove the horizontal stabilizer from the fuselage, carefully cut away the covering inside the lines which were marked in steep 1. 3-Speared epoxy onto the bottom and top of the horizontal stabilizer along the area where the covering was removed in the previous step and to the fuselage where the horizontal stabilizer mounts.
PAGE 7
11- Tail gear / Heckspornrad FUSELAGE - BOTTOM VIEW UNTERSICHT 1-Place the tail gear mount on the bottom 1/8x15/32” of the fuselage as show, mark the (3x12mm) screw mounting hole positions with a pencil. ...........2 2-Remove the tail gear mount from the Tail gear horn fuselage, Drill the two mounting holes as marked. ...............1 3-Cut a 5/64”(2mm) wide slot which is 5/16” 5/64”(2mm) collar (8mm) length and 5/16”(8mm) depth on ...............1 the bottom of the rudder as shown.
PAGE 8
14- Brushless motor Firewall A A=A’ A’ Bolts, nuts and washer are not supplied 15- FRONT-VIEW 135mm (5-5/16”) SIDE-VIEW Fuel tank / Treibstofftank To muffler Filler tube Rubber stopper X Cap Stopper 16- To engine Fuel tube After confirming the direction, insert this assembly, clunk end first, into the fuel tank and tighten and screw the fuel tank cap on firmly. Cowling / Motorhaube 2.5x10mm.....3 1.5mm 1.
PAGE 9
18- Linkages / Anlenkungen Connector ........ 3 Connector Connector Rudder pushrod ...... 1 Elevator pushrod Rudder servo Elevator servo Fuel tank FUSELAGE - BOTTOM VIEW UNTERSICHT 19- ABS Shield FUSELAGE - BOTTOM VIEW UNTERSICHT CA CA Cut away only the covering 1-Using the ABS shield as a template, trace around the outside edge of the ABS shield, and then remove it. 2-Using a sharp hobby knife, cut away the covering inside the lines. Not to cut into the wood.
PAGE 10
20- Canopy / Kabinenhaube 2x10mm screw ............4 1.5mm 21- Decor / Aufkleber CHINESE AIR-FORCE VQA022C AVG CHECKER TAIL VERSION UD ST VQA020B US.ARMY Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing.
PAGE 11
22- Balance / Schwerpunkt 4”~4-1/8” (100~105mm) DO NOT try to fly an out-of-balance model ! Note: If necessary, move the battery pack or add weight to either the tail or nose until the correct balance is achieved.