User Manual

ManualsBrandsVQ Model ManualsAircraftsP-38 Ligthning

Table Of Contents

Radio control model

Wingspan approx. 83 in.

Fuselage length approx. 57.5 in.

Glow Engine 7.45cc 2T /11.5cc 4T (x2)

Electric Motor 870 Watt Brushless motor x2

Radio 6 Channel / 10 Servos

INSTRUCTION MANUAL

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of control and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

LEGEND MODELS

Summary of content (20 pages)

PAGE 1
Radio control model INSTRUCTION MANUAL Wingspan approx. 83 in. Fuselage length approx. 57.5 in. Glow Engine 7.45cc 2T /11.5cc 4T (x2) Electric Motor 870 Watt Brushless motor x2 Radio 6 Channel / 10 Servos L LEGEND MODELS WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of control and cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
PAGE 2
REQUIRED ITEMS Electric Set up 1: 2X Dualsky XM5050EA-7 610Kv motors. 2X Dualsky XC8018BA 80A ESC, 100A burst 2X Dualsky XP45004EX 4S, 35C, 4500mAh Lipo 2X Prop: 14x9 x3-blade Master Airscrew Approx Weight: 1600grams / 3.6lbs Minimum 6 channel radio for airplane / 8-10 servos. .60 - .70 cu.in (x2) 10cc - 11.5cc (x2) .46 - .50 cu.in.(x2) 7.45cc (x2) Connector Electric Setup 2: 2X Dualsky XM5060EA-6 470Kv motors.
PAGE 3
1-Wing Connector Flap push rod Servo mount Connector (included) ........2 1A Install the push rod connector onto the outer-most hole of the flap servo arm. 1B Flap servo -Turn the center wing over. -Turn the four screws and move the hatch out of the wing. -Place the flap servo onto the servo mount with the flap push rod installed as shown. -Using the pencil, trace around the servo, where it meets the servo mount. Adhesive tape (included) 1C Remove the servo out of the wing.
PAGE 4
2-Wing CENTER WING Bottom-view The center wing with the flaps in closed position. Note: Do not close the hatches in this time The center wing with the flaps in opened position.
PAGE 5
3-Wing Connector Connector ........2 .............2 3A 2x30mm screw .......4 Note: the connector is turn-down Note: the connector is turn-down Servo mount Flap push rod From Step 3B to Step 3I, follow the procedure as described in the 1-WING section To be connected the extension with the aileron servo cord before attach the hatch to the wing Note: the aileron extension must 700mm long or use two 300mm long.
PAGE 6
4-Wing Slide the aluminum tube into the left and right side of the center wing. 19x317mm aluminum tube Do the same way with the other side of the center wing. 12x182mm aluminum tube ...2 6x12mm wooden dowel 19x317mm aluminum tube 12x182mm aluminum tube ......................2 6x12mm wooden dowel ......................
PAGE 7
5-Wing !Check the ailerons and flaps functions move in the correct before attach all hatches to the bottom of the wing. Carefully, slide the left wing to meet the center wing .....2 4x20mm screw .............
PAGE 8
6-Engine mounts TOP 5.5mm A A B=B’ B BOTTOM B’ Align the mark on both mounts with the center mark on the balk head. B 6A B’ ! Align the mark on both mounts with the center mark on the balk head. 4x30mm screw ..8 .............8 Blind-nut ................8 ! Engine thrust on balk head is already adjust at factory 6B L/R 7-Engine 132~134mm C= 132 ~ 134mm C SIDE-VIEW Secure the engine to the engine mount using four 3x25mm screws Insert the Z-bend into the hole on the throttle lever of engine.
PAGE 9
8-Electric Motor TOP Align the mark on the motor mounting plate with the center mark on the balk head. 8A 3mm Using a aluminum motor mounting plate as a template, mark the plywood motor mounting plate where the four holes are to be drilled. Remove the aluminum motor mounting plate and drill a 1/8”(3mm) hole through the plywood at each of the four marks marked . Note: The aluminum motor mounting included with electric motor set. 8B Firewall SIDE-VIEW X L/R BOTTOM 5mm 8C B B=B’ B’ 5x70mm..
PAGE 10
-Hatch L/R Bottom hatch Bottom hatch Cut away only the covering 30x4mm nylon bolt ............4 Secure the Bottom hatch in place using the 30x4mm nylon bolt. FUSELAGE - Bottom view 11-Servos RIGHT FUSELAGE - Top view Throttle servo tray Note: Turn the throttle servo tray for other engine if needed.
PAGE 11
12-Rudder .............2 2x30mm screw .......4 L/R CA 15mm 2 mm 13-Fixed gear Main landing gear 3x12mm screw 3x12m ..........8 3x15mm screw ..........8 Nylon gear strap Square plastic x 2 3x20mm screw ......16 2mm Gear mount 2mm Nylon gear strap Square plastic .......4 Ply gear mount plate x 2 3x15mm 13A .........4 Gear mount x 2 Ply gear mount flat 13B 13C 4.
PAGE 12
14-Nose gear 4.7mm nose gear Nose gear push rod Nose gear arm 3x20mm...4 Washer.....4 Nut 3mm...
PAGE 13
17-Horizontal Stabilizer ABS “balance” HORIZONTAL STABILIZER Top-view 2 mm .............2 CA Cut away onlly the covering ABS “balance” 2x30mm screw .......4 18-Horizontal Stabilizer LEFT FUSE. RIGHT FUSE. B=60mm B=60mm A=8mm A=8mm A A B B A 6x60mm Wooden dowel Secure the aluminum tube and wooden dowel in place using Thin CA glue A L/R 12x108mm aluminum tube ....2 6x60mm wooden dowel ................
PAGE 14
20-Horizontal Stabilizer 20A TOP 2.mm Drill through both the balsa block and aluminum tube 2.
PAGE 15
23-Installing the main fuselage 6x50mm plastic bolt 10mm ....1 WING FIBER GLASS MAIN FUSELAGE 24-Installing the cockpit FIBER GLASS COCKPIT Secure the cockpit in place using 2x8mm screws FIBER GLASS MAIN FUSELAGE 25-Cowling 2.5x12mm screw Secure the cowl in place using ...........8 2.5x12mm screws COWL BOTTOM VIEW COWL BOTTOM VIEW L R Note: The “L” Cowl for LEFT fuselage and “R” Cowl for RIGHT fuselage (looking from REAR to FRONT and TOP view).
PAGE 16
27-Gear door CA 27A CA Frame Fuselage Fuselage CA Hinge Gear door GEAR DOOR IN OPENED POSITION Gear door Frame Note: you can find the same spring in old ball-point pen Spring (not include) Cotton thread Gear door (not include) 27B Gear door Fuselage Fuselage Cotton thread (not include) Cotton thread (not include) Spring (not include) ALL GEAR DOORS IN OPENED POSITION ALL GEAR DOORS IN CLOSED POSITION (RETRACT LANDING GEAR IN RETRACTED POSITION) (RETRACT LANDING GEAR IN EXTENDED POSITI
PAGE 17
28-Gear door Gear door (main fuselage) 28A 28B 28C CA Cotton thread (not include) CA Balsa block (not include) Spring (not include) CA CA Gear door 28D Bottom-view
PAGE 18
29-Gear door Cotton thread CA Fuselage side Hinge Cotton thread (not include) GEAR DOOR IN CLOSED POSITION (NOSE RETRACT LANDING GEAR IN RETRACTED POSITION) GEAR DOOR IN OPENED POSITION Gear door GEAR DOOR IN OPENED (RETRACT LANDING GEAR IN EXTENDED POSITION) POSITION 30-Canopy 1.2mm 2x8mm screw ...................6 2x8mm screw 1.
PAGE 19
32-Decal IMPORTANT: Please do not clean your model with pure alcohol, gasoline or strong sloven, only use kerosene or liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade.
PAGE 20
33-Installing the guns CA 34-Balance WARNING: Never fly before checking the Cg’s required position. 115 ~ 120mm 115~120mm WING ROOT The ideal C.G. position is 115 ~ 120mm behind the leading edge. 35-Control ranges 8~10mm AILERON 8~10mm FLAP 30~35mm 25~30mm RUDDER Position for right diagram. 25~30mm Position for right diagram.