60 Class 2-cycle engine MESSERSCHMITT ME-108 90 Class “Taifun” 4-cycle engine BUILDING INSTRUCTIONS / MONTAGEANLEITUNG VQA053 SPECIFICATIONS Wingspan Length Flying weight Electric Motor Glow Engine Radio 1625mm 1300mm 2900g 800 Watt (BOOST 60) 10cc 2T / 15cc 4-T 6 Channel / 7 Servos Technische Daten Spannweite Länge Fluggewicht Elektroantrieb Verbrennerantrieb Fernsteuerung 1625mm 1300mm 2900g 800 Watt (BOOST 60) 10cc 2T / 15cc 4T 6 Kanal / 7 Servos WARNING! This radio controlled model is NOT a t
REQUIRED FOR OPERATION (Purchase separately) BENOTIGTE KOMPONENTEN FUR DEN ABFLUG (Nicht enthalten) 12x6 for .60 - 4 cycle engine 13x7 for .90 - 4 cycle engine 14X8 for Quantum 4120/07 BOOTS 60 Phoenix-60 Brushless Motor Control or equivalent. Extension for aileron servo, retract servo. Retract landing gear VQAR010 Retract servo x1 Minimum 6 channel radio for airplane with 7 servos .Motor control x1 .Aileron x2 .Elevator x1 .Rudder x1 .Flap x 2 .
1- Joining the wing / Flachenverbindung TOP VIEW / AUFSICHT A B A B Nylon wing bolt Rubber band (both the top and bottom) IMPORTANT: Please do not clean off the excess epoxy on the wing with strong solvent or pure alcohol, only use kerosene to keep the colour of your model not fade.
- Flap, Aileron servo / Flap, querruder servo Connector 2mm WING - BOTTOM VIEW UNTERSICHT Aileron extension cord exit Aileron extension cord ...........4 Plastic control horn X ...........4 set Aileron servo hatch Flap servo hatch flap extension cord Aileron servo hatch 2x10mm Flap servo hatch Servo mount 2x10mm 1.5mm Servo mount 1.
- Retract landing gear / Einziehfahrwerk ...2 Trial fit the push rod into the wing. Join the pushrod to the retract gear arm and trial fit the retract into the wing. ...2 Pull and push the retract push rod by hand to be sure to adjust the stroke so that the landing gear locks in both up and down position. Clevis Connector Retract landing gear Retract push rod Do the same way with other half wing.
7- Fixed gear / Starres Fahrwerk 3x20mm screw ..........8 3x20mm screw ......16 3x20mm Main landing gear 2mm Nylon gear strap Ply gear mount flat 2mm Nylon gear strap .......4 Square plastic Gear mount 2 1 3x20mm 3 8- Fixed gear / Starres Fahrwerk ........2 Do the same way with other half wing. 5/32”(4mm) collar ..........2 1/8x13/32”(3x12mm) ..........8 5/64x15/64”(2x6mm) ..........4 3x12mm screw FRONT 2 mm Gear cover 5/64 (2x6mm) screw 1/16 1.
10- Horizontal Stabilizer / Hohenleitwerk Cut away only the covering both the right and left side 1-Trial fit the horizontal stabilizer in place . Check the alignment of the horizontal stabilizer. When you are satisfied with the alignment, use a pencil to trace around the right and left of the stabilizer where it meets the fuselage. 2-Remove the horizontal stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above.
13- Rudder / Seitenruder Plastic control horn ...........3 set Apply a thin layer of machine oil or petroleum jelly to only the pivot point of the hinges on the rudder, then push the rudder and its hinges into the hinge slots in the trailing edge of the vertical stabilizer. There should be a minimal hinge gap. When satisfied with the and alignment, hinge the rudder to the vertical stabilizer using 5 minute epoxy.
16- Tail Brace / Leiwerksstutze ABS Shield 4 1-Position the tail brace in place (1). Using the pencil mark the location of the two brace holes as show (2). 2-Remove the tail brace and drill two 1/16” (1.5mm) as show (3). 3-Slide the two ABS cover on to the right and left tail brace as show (4) 4-Position the tail brace again. Secure it in place with two 2x12mm screws (5) 2 3 1/16” 1.5mm Brace 5 1/16” 1.5mm 4 ABS Shield Vis 3x12mm .......4 1/16” 1.
18- Fuel tank / Treibstofftank To muffler Filler tube Rubber stopper 3x25mm screw To engine 19- X Brushless Motor 4mm After confirming the direction . Insert this assembly, clunk end first, into the fuel tank and tighten and screw the fuel tank cap on firmly. Using a aluminum motor mounting plate as a template, mark the plywood motor mounting plate where the four holes are to be drilled (2).
20- Li-Po battery stand Magnetic battery hatch 1 Li-Po battery stand 2 Secure the Li-Po battery stand using four 2x10mm screws 3 In case of brushless motor using.
FUSELAGE BOTTOM-VIEW UNTERSICHT Tail wheel pushrod Rudder servo Servo mount 21- Servo installation FUEL TANK Rudder pushrod Servo mount Elev. Pushrod (x2) Throttle pushrod Throttle servo Elevator servo Elevator pushrod 3mm set Screw 3mm set Screw Elevator pushrod or rudder pusshrod D=5/64”(2mm) Tail wheel pushrod D=.050”(1.2mm) throttle pushrod D=.050”(1.2mm) 2 mm 2 mm X Connector X ................2 2mm ....................
3/32x25/64” self tapping screw 2.5x10mm .................5 23- Cowling / Motorhaube 1-Attach the board or transparent plastic on the side of the fuselage with the adhesive tape as show. Adhesive tape 2-Using a pencil or felt tipped pen trace around the engine head where it meet the cowl. Cut the opening the board or transparent plastic for the engine head as marked before.
24- Canopy / Kabinenhaube 3/32x25/64” self tapping screw 2x6mm .................10 1/16” 1.5mm BOTTOM-VIEW UNTERSICHT 25- ABS Shield Vis 2x10mm .......6 ABS Shield 1/16” 1.5mm CA ABS Shield CA ABS pushrod exit guider CA ABS Shield Slide the two ABS in place and secure them with CA glue.
26- Wing installation BOTTOM-VIEW UNTERSICHT 6x50mm Nylon bolt CA 6x50mm Nylon bolt ....2 27- Balance / Schwerpunkt Note: Adjust the location of the battery pack to achieve this C.G location.
