Parent’s Guide F.P.
INTRODUCTION Thank you for purchasing the VTech® Kidi DJ Mixer. VTech® Kidi DJ Mixer features easy music creation in different styles. 1 2 3 4 F.P.
INCLUDED IN THIS PACKAGE • One Kidi DJ Studio • One parent’s guide WARNING All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your child’s safety. NOTE Please keep this parent’s guide as it contains important information.
GETTING STARTED This product is in Try-me mode in the packaging. Press and hold the Customize sound effect button 5 for a few seconds to proceed with normal play. If the unit powers down during the play, please install a new set of batteries. Battery Removal and Installation 1. Make sure the unit is turned Off. 2. Find the battery cover located on the back of the unit, use a screwdriver to loosen the screw and then open the battery cover. 3. Remove old batteries by pulling up on one end of each battery. 4.
BATTERY NOTICE • • • • • • • • Insert batteries with the correct polarity (+ and -). Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries. Only batteries of the same or equivalent type as recommended are to be used. Do not short-circuit the supply terminals. Remove batteries during long periods of non-use. Remove exhausted batteries from the toy. Dispose of batteries safely. Do not dispose of batteries in fire.
MISE EN GARDE Les piles fournies avec le produit permettent de tester le jouet en magasin mais ne sont pas des piles longue durée. • Mettre en place les piles ou les accumulateurs en respectant les polarités + et –. • Ne pas mélanger des piles ou des accumulateurs neufs avec des usagés. • Ne pas mélanger différents types de piles : alcalines, zinc-carbone et rechargeables. • Seules des piles du type recommandé doivent être utilisées.
PRODUCT FEATURES 1. POWER BUTTON Press the Power Button to power on the unit. Press the button again to power off the unit. 2. LINE-IN JACK Connect external player 3. EXTERNAL SPEAKER JACK Connect external speaker or headphone 4. AC ADAPTER Connect AC adapter power 5. AUTOMATIC SHUT-OFF To preserve battery life, the KidiGo™ Fast Break Hoop will automatically turn off after 10 minutes without input. The unit can be turned on again by pressing the Power Button.
GAMES DJ Party Launch pad buttons Use the Launch pad buttons to choose different instruments sounds to play. Each column allows one button to be playing. The selected option is lit up. Preset sound effect buttons Press the Preset sound effect buttons to add build-in sound effects. Style button Press Style button to change the music for the Launch pad buttons and Build-in sound effect buttons Customize SFX buttons Hold to record your own short sound effect.
Bluetooth connect button and Bluetooth button Press Bluetooth connect button to connect a Bluetooth device. After the device is connected, press Bluetooth music button to play the Bluetooth external source sound Crossfader Use the crossfader to adjust the volume balance between Build-in / Line-in / Bluetooth sound and the Launch pad. Tempo control Use the Tempo control buttons to adjust. the tempo of the Launch pad music. Pause button Press Pause button anytime to stop all sound.
Record Select the track you would like to record. After the countdown, recording starts. The unit can record the Turntable, Build-in button, Launch pad, preset sound effects, customize sound effect, crossfader behaviour and tempo change status. When finish, press OK button to save your recording. Note: If you have customize the customize sound effect later on, the customize sound effect in the recorded track will change too.
Environmental Phenomena The unit may malfunction if subjected to radio-frequency interference. It should revert to normal operation when the interference stops. If not, it may become necessary to turn the power off and back on, or remove and reinstall the batteries. In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory, requiring the user to reset the device by removing and reinstalling the batteries.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Visit our website for more information about our products, downloads, resources and more. www.vtechkids.com www.vtechkids.ca Read our complete warranty policy online at www.vtechkids.com/warranty www.vtechkids.ca/warranty TM & © 2021 VTech Holdings Limited. All rights reserved. Printed in China.
