User's Manual

ManualsBrandsVTech Telecommunications ManualsAudio EquipmentDECT 6.0 Cordless Headset

Connect to a Computer

A. Connect USB

1. Plug the small connector on the end of the USB cable provided into the

micro USB port on the side of the base.

2. Plug the other end into the USB port on your computer.

3. Wait for your operating system to indicate that it has recognized the headset

and that it is ready to use.

B. Conﬁgure Computer Audio Settings

1. Press the PC button on the base. The PC indicator LED will be lit red.

2. Go to your computer’s audio settings and make sure that “VXi V200” is

selected under both playback and recording.

3. If necessary, make sure the “VXi V200” is also selected for use in your

communications software settings.

Position Base

To reduce the possibility of noise and interference problems, position the base at

least 6 inches away from your desk phone and at least 12 inches away from your

computer.

How to Wear

Changing Wearing Styles

The V200 ofﬁce wireless headset is

supplied with a choice of wearing styles:

Ear Hook

A. Choose the ear bud that ﬁts your ear

most comfortably.

B. Place the ear bud over the post on the

ear hook.

C. Attach the ear hook to the headset by

placing it over the earpiece and gently

pressing it into position.

D. Loop the ear hook over the ear and

rotate the headset so the microphone is

angled toward the mouth.

Headset Overview

A. Mute

B. Call Control On/Off

C. Volume +/-

D. Earpiece

E. Battery Cover

F. Headset Charging Contacts

G. Microphone

Base Overview

Front

A. Headset Docking/Charging Cradle

B. PC Button/LED

C. Mute LED

D. Phone Button/LED

E. Pairing Button

Back

A. Micro-USB Port

B. EHS/Lifter Port

C. Power Port

D. Analog Telephone Port

E. Base Jack Port

F. Handset Port

Right Side

A. Headset Microphone

Level Adjustment Buttons

B. Mode Button

C. Micro-USB Port

Left Side

D. Phone Compatibility Switch

Connect to Your Phone and Computer

Connect Power to Base

A. Remove the panel from the bottom of the base.

B. Connect the power adapter cable into the base power port (green dot) and plug

the power adapter into an electrical socket.

Install Battery and Charge Headset

A. Remove the battery cover from the headset.

B. Insert the battery into position with the label “THIS SIDE UP” facing up.

C. Connect the battery lead to the headset.

D. Replace the battery cover and place the headset in the charging cradle.

The LED on the headset will be red when charging and will change to blue

when the headset is fully charged.

Connect and Conﬁgure Ofﬁce Phone

A. Remove the panel from the

bottom of the base.

B. Connect the base jack cable

(orange ﬂag) to the base

jack port (orange dot) on the

base and the other end to the

headset port of the phone.

If you do not have a headset

port, you will need to use the

handset port.

C. Check Conﬁguration and Make a Test Call:

1. Set your desk phone volume to mid-range.

2. Make sure the base shows the phone output is selected. A green LED

indicates the mode is set for ofﬁce phone use. If it is red, press the mode

button on the side of the base to change to the correct mode.

3. Check that the phone compatibility switch on the side of the base is correct

for your phone. Most phone makes use setting D (default), but many Cisco

phones will use setting A.

4. Open the headset line on your desk phone, or remove the handset from the

cradle if you are connected to the handset port.

5. While wearing the headset, press the call control button on the headset.

6. If you do not hear a dial tone (or tones) when pressing the dial pad buttons,

try the other base compatibility switch settings until you do.

7. Dial a test call from the desk phone.

i. You can ﬁne-tune the earpiece volume using the headset volume buttons.

ii. If additional microphone gain (speaking volume) is needed, or if you hear

your voice echo in the earpiece (excessive side tone), you can adjust this

with the microphone volume buttons on the side of the base.

Other Connection Conﬁgurations

In addition to the standard setup, there are three more options for setting up the

V200 with your phone:

A. Ofﬁce Phone with EHS (sold separately)

B. Ofﬁce Phone with L50 Lifter (sold separately)

C. Analog (Home) Phone

For more details, see the full user guide, available online at vxicorp.com/V200.

VXi V200

Quick-Start Guide

VXi Corporation | 271 Locust Street, Dover, NH 03820 USA

USA Toll Free: 800-742-8588 | Phone: +1 603-742-2888

vxicorp.com

PN 203940/APN 203944X

Headband

A. Position the headset earpiece

over the headband ring and

press until it clicks into place.

B. Angle the headset so the

microphone boom points

toward the corner of the mouth.

C. Slide the headband in or out to

adjust ﬁt.

Neckband

A. Position the headset earpiece over the

neckband ring and press until it clicks

into place.

B. To wear, position the neckband around

the back of the neck and over both ears.

Angle the microphone boom toward the

corner of the mouth.

C. To switch neckband wearing sides,

remove the headset from the neckband,

and then remove the ring from the

neckband arm. Insert the ring post into

the bottom hole of the other neckband

arm until it clicks into place.

06/16

A F

B E

C D

Left Side

Right Side

Need More Help?

Technical Support

www.vxicorp.com/support

Online User Guide

www.vxicorp.com/V200

Functions and Indicators Tables

Base/Headset Function Button/Duration of press Base LED Indicator Headset LED Indicator Headset Audio Indicator Voice Indicator (in English)

Base PC Output Path PC (quick press) Red PC LED - - -

Base Phone Output Path Phone (quick press) Green or Red PC LED - - -

Base Analog Phone Mode Mode (quick press) Red Phone LED - - -

Base

Ofﬁce (Digital/VoIP) Phone

Mode

Mode (quick press) Green Phone LED - - -

Base

Conference PC with active

Phone Call

PC (press and hold)

PC and Phone LEDs ﬂash

together

- 3 beep rising tone -

Base

Conference Phone Call with

active PC Call

Phone (press and hold)

PC and Phone LEDs ﬂash

together

- 3 beep rising tone -

Base

Headset

Base/Headset Function Button/Duration of press Base LED Indicator Headset LED Indicator Headset Audio Indicator Voice Indicator (in English)

Headset Charging in base station - -

Red while charging,

Blue when charged

- -

Headset Volume Up Volume Up (quick press) - - 1 short tone -

Headset Volume Down Volume Down (quick press) - - 1 short tone -

Headset

Maximum or minimum

volume reached

Volume Up or Volume Down

(quick press)

- - 3 quick beeps -

Headset Mute (On/Off) Mute Button, (quick press) - - 1 short tone -

Headset Mute Reminder - Red Mute LED - 1 tone (every 15 seconds) -

Headset Answer a Call

Call Control Button (quick press)

Blue light ﬂashes slightly slower

1 short tone -

Headset End a Call

Call Control Button (quick press)

Blue light ﬂashes slightly faster

1 short tone -

Headset Out of range Any Headset Button - - - “Out of range”

Headset Very low battery - -

Flashes 3 times, pauses,

repeats 3 more times, then

shuts down

Headset Low battery - -

Flashes every 20 seconds

“Low battery”

Headset Incoming call (Analog Mode) - - Flashes quickly - -

Headset

Answer Second Incoming Call

(Analog Mode Only)

Mute Button, (long press) - - 1 short tone -

Headset Headset Not Registered Any Headset Button Press -

Red and Blue alternating

ﬂash

- “Not registered”

Besoin d’aide supplémentaire?

Assistance technique

www.vxicorp.com/support

Guide d’utilisation en ligne

www.vxicorp.com/V200

¿Necesita más ayuda?

Asistencia técnica

www.vxicorp.com/support

Guía del usuario en línea

www.vxicorp.com/V200

Tablas de funciones e indicadoresTableaux de fonctions et indicateurs

Base/Auricular Función Botón/Mantener presionado... Indicador LED de la base Indicador LED del auricular Indicador de audio del auricular Indicador de voz (en inglés)

Base Trayectoria de salida de PC PC (presionar rápidamente) LED PC rojo - - -

Base Trayectoria de salida del teléfono Teléfono (presionar rápidamente) LED PC verde o rojo - - -

Base Modo de teléfono analógico Modo (presionar rápidamente) LED Teléfono rojo - - -

Base Modo de teléfono de oﬁcina (digital /VoIP) Modo (presionar rápidamente) LED Teléfono verde - - -

Base

PC para conferencias con una llamada

activa

PC (presionar y mantener)

LED de PC y Teléfono

parpadean juntos

- 3 tonos ascendentes -

Base

Llamada telefónica en conferencia con

una llamada de PC activa

PC (presionar y mantener)

LED de PC y Teléfono

parpadean juntos

- 3 tonos ascendentes -

Base/oreillette Fonction Bouton/durée d’appui Indicateur DEL de la base

Indicateur DEL de l’oreillette Indicateur audio de l’oreillette Indicateur vocal (en anglais)

Base Chemin de sortie de l’ordinateur Ordinateur (pression rapide) DEL rouge d’ordinateur - - -

Base Chemin de sortie du téléphone Téléphone (pression rapide) DEL d’ordinateur verte ou rouge - - -

Base Mode téléphonique analogique Mode (pression rapide) DEL rouge d’ordinateur - - -

Base Mode téléphonique (numérique/VoIP) Mode (pression rapide) DEL verte du téléphone - - -

Base

Conférence par ordinateur avec

fonction d’appels téléphoniques

activée

Ordinateur (tenez enfoncé)

Les DEL de l’ordinateur et

du téléphone clignotent

simultanément

- Ton montant à 3 bips -

Base

Conférence téléphonique avec fonction

d’appels sur ordinateur activée

Téléphone (tenez enfoncé)

Les DEL de l’ordinateur et

du téléphone clignotent

simultanémentogether

- Ton montant à 3 bips -

BaseBase

Auricular

Oreillette

Base/Auricular Función Botón/Mantener presionado... Indicador LED de la base Indicador LED del auricular Indicador de audio del auricular Indicador de voz (en inglés)

Auricular Carga en estación base - -

Rojo durante la carga. Azul

cuando se completa la carga.

- -

Auricular Subir volumen

Subir volumen (presionar

rápidamente)

- - 1 tono breve -

Auricular Bajar volumen

Bajar volumen (presionar

rápidamente)

- - 1 tono breve -

Auricular Se alcanzó el volumen máximo o mínimo

Subir volumen o bajar volumen

(presionar rápidamente)

- - 3 pitidos breves -

Auricular Silencio (Activar/desactivar)

Botón Silencia (presionar

rápidamente)

- - 1 tono breve -

Auricular Recordatorio de silencio activado - LED rojo Silencio - 1 tono (cada 15 segundos) -

Auricular Contestar una llamada

Botón de control de llamada

(presionar rápidamente)

Parpadea en azul un poco más

lento

1 tono breve -

Auricular Finalizar una llamada

Botón de control de llamada

(presionar rápidamente)

Parpadea en azul un poco más

rápido

1 tono breve -

Auricular Fuera de alcance Cualquier botón del auricular - - - "Fuera de alcance"

Auricular Muy poca batería - -

Parpadea 3 veces, pausa,

repite 3 veces más y se

apaga

Auricular Poca batería - -

Parpadea cada 20 segundos

"Poca batería"

Auricular Llamada entrante (modo analógico) - - Parpadea rápidamente - -

Auricular

Contestar llamada entrante (mono

analógico únicamente)

Botón Silencio (presionar por un

momento)

- - 1 tono breve -

Auricular Auricular no registrado

Presionar cualquier botón del

auricular

Rojo y azul parpadean

alternativamente

- "No registrado"

Base/oreillette Fonction Bouton/durée d’appui Indicateur DEL de la base

Indicateur DEL de l’oreillette Indicateur audio de l’oreillette Indicateur vocal (en anglais)

Oreillette Chargement dans la station de base - -

Rouge pendant le

chargement. Bleu une fois le

chargement terminé.

- -

Oreillette Volume + Volume + (pression rapide) - - 1 brève tonalité -

Oreillette Volume - Volume - (pression rapide) - - 1 brève tonalité -

Oreillette Volume maximum ou minimum atteint

Volume + ou volume -

(pression rapide)

- - 3 bips rapides -

Oreillette Mise en sourdine (activée/désactivée)

Bouton Mise en sourdine

(pression rapide)

- - 1 brève tonalité -

Oreillette Rappel de mise en sourdine - DEL de mise en sourdine rouge -

1 tonalité (toutes les 15 secondes)

Oreillette Répondre à un appel

Bouton de contrôle des appels

(pression rapide)

Une lumière bleue clignote un peu

plus lentement

1 brève tonalité -

Oreillette Mettre ﬁn à un appel

Bouton de contrôle des appels

(pression rapide)

Une lumière bleue clignote un peu

plus rapidement

1 brève tonalité -

Oreillette Hors de plage Tout bouton d’oreillette - - - «Hors de portée»

Oreillette Pile très faible - -

Clignote 3 fois, fait une

pause, répète l’action trois

autres fois, puis se ferme

Oreillette Pile faible - -

Clignote toutes les 20 secondes

«Pile faible»

Oreillette Appel entrant (mode analogique) - - Clignote rapidement - -

Oreillette

Répond au deuxième appel entrant

(mode analogique seulement)

Bouton Mise en sourdine

(longue pression)

- - 1 brève tonalité -

Oreillette Oreillette non enregistrée

N’importe quel bouton de

l’oreillette enfoncé

Rouge et bleu clignotent en

alternance

- «Non enregistrée»

Summary of content (2 pages)

PAGE 1
Headset Overview A. Mute B. Call Control On/Off C. Volume +/D. Earpiece E. Battery Cover F. Headset Charging Contacts G. Microphone VXi V200 Quick-Start Guide Right Side A. Headset Microphone Level Adjustment Buttons B. Mode Button C. Micro-USB Port D A C B E A B C F Left Side D. Phone Compatibility Switch G C. Check Configuration and Make a Test Call: 1. Set your desk phone volume to mid-range. 2. M ake sure the base shows the phone output is selected.
PAGE 2
Vue d’ensemble de l’oreillette Guide de démarrage rapide VXi V200 Côté droit A. Boutons de réglage du niveau sonore du microphone de l’oreillette B. Bouton Mode C. Port micro-USB D A. Mise en sourdine B. Contrôle des appels Marche/arrêt C. Volume +/D. Écouteur E. Couvercle du logement de la pile F. Contacts de chargement de l’oreillette G. Microphone A C B E Installation de la pile et chargement de l’oreillette A. Retirez le couvercle du logement de la pile de l’oreillette. B.