User's Manual

User’s manual
VM5231
Accessory baby unit
for use with VTech model
VM5271 / VM5271-2
Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
This manual has instructions on how to set
up and pair your new baby unit. For complete
instructions on using the baby unit, see the
user’s manual that comes with your video and
audio monitor.
For support, shopping, and everything new at
VTech, visit our website at
www.vtechphones.com.
Register online to get an additional
3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for
enhanced warranty support.
Product news
Learn about the latest VTech
products.
What’s in the box
Connect the baby unit
NOTE
S
• Use only the power adapter supplied with this
product.
• Make sure the electrical outlet is not controlled by
a wall switch.
• The power adapter is intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if they are plugged into a ceiling, under-the-table
or cabinet outlet.
• Make sure the baby unit and the power adapter
cord are out of reach of children.
Overview
1
Motorized lens with 6x optical zoom
2
Light sensor
3
Microphone
4
Speaker
5
Skip
• Press to play the next lullaby.
6
Play/Stop
• Press to play or stop lullaby on the
baby unit.
7
- VOLUME +
• Press to adjust the baby unit
speaker volume. It determines the
lullaby volume and talkback volume
transmitted from the parent unit.
8
POWER light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed; or when the link to the
parent unit is lost.
9
Antenna
10
Temperature sensor
11
Power jack
12
ON/OFF switch
• Slide to turn on or off the baby unit.
13
PAIR
• Your baby units and parent unit
provided are already paired.
• Press and hold on accessory baby
units to pair to the parent unit.
14 Threaded socket
• For wall mount installation use.
Before use
Pair new baby unit
Each newly purchased baby unit (VM5231)
must be paired to your video and audio monitor
system (VM5271 / VM5271-2).
NOTE
S
• You can pair a maximum of four baby units to your
parent unit. Each new baby unit must be paired to
the parent unit before use.
• Make sure you power on the parent unit before
pairing.
1. Press MENU when the parent unit is idle.
2. Press or to choose Pair/Unpair CAM,
then press SELECT.
3. Press SELECT again to choose Pair CAM.
4. Press or to choose an empty baby unit
slot, then press SELECT.
5. The parent unit screen displays Press
and hold the pair button at the CAM
for 5 seconds until the power indicator
flashes.. Immediately press and hold PAIR
on the bottom of the baby unit. The LED
light flashes quickly.
When pairing is successful, the screen
displays the view of newly paired baby unit in
SINGLE-CAM mode. The LED light on the
new baby unit remains on.
NOTE
S
• If pairing fails, the screen displays Pairing failed.
Try the pairing process again.
• Only one baby unit can be paired at a time.
Positioning the baby monitor
CAUTION
• Keep the baby units out of the reach of your baby.
Never place or mount the baby units inside the
baby’s crib or playpen.
NOTE
• To avoid interference from other electronic
devices, place your baby monitor far away from
devices such as wireless routers, microwaves, cell
phones and computers.
1. Place the baby units more than 1 meter
(3 feet) away from your baby.
> 1m (3ft)
> 1m (3ft)
2. Adjust the angle of the baby unit camera to
aim at your baby.
3. Place the parent unit more than 1 meter
(3 feet) away from the baby units.
CAUTION
• This baby monitoring system includes a
special lens which is capable of optical zoom
and requires delicate treatment. Please avoid
disassembling, dropping, or any other rough
handling.
• The default volume of your parent unit is level 4.
If you experience high-pitched screeching noise
from your baby monitor while positioning:
- Make sure your baby units and parent unit are
more than 1 meter (3 feet) apart, OR
- Turn down the volume of your parent unit.
Mount the baby monitor (optional)
NOTE
• Check for reception strength and camera angle
before drilling the holes.
1. Place the wall mount bracket on a wall and
then use a pencil to mark the top and the
bottom holes as shown. Remove the wall
mount bracket and drill two holes in the wall
(7/32 inch drill bit).
2. If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than
a stud, insert the wall anchors into the holes.
Tap gently on the ends with a hammer until
the wall anchors are flush with the wall.
3. Align the wall mount bracket and screws
with the holes in the wall as shown. Tighten
the screw in the middle hole first, so that the
wall mount bracket position is fixed. You can
tighten the other screw in the top hole.
Place the baby unit on the wall mount
bracket. Tighten the screw into the threaded
socket at the bottom to secure the baby unit.
-OR-
Insert the screws into the holes and tighten
the screws until only 1/4 inch of the screws
are exposed.
Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket
at the bottom to secure the baby unit. Align
the holes on the wall mount bracket with the
screws on the wall, and slide the wall mount
bracket down until it locks into place.
4. The default angle of the wall mount bracket
is 90 degrees. You can maximize your
baby unit’s viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob
in anticlockwise direction. This will loosen
the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to
your preferred angle. Then, rotate the knob
in clockwise direction to tighten the joint and
secure the angle.
Operating range
The operating range of the baby monitor is
up to 300 meters (1,000 feet) outdoors or
50 meters (160 feet) indoors. The actual
operating range may vary depending on
the environmental conditions and other
interferences such as walls, doors and other
obstructions.
Unpair a baby unit
NOTE
Make sure you power on the baby unit and the
parent unit before unpairing the baby unit.
1. Press MENU when the parent unit is idle.
2. Press or to choose Pair/Unpair CAM,
then press SELECT.
3. Press or to choose Unpair CAM, then
press SELECT.
4. Press or to choose a desired baby unit,
then press SELECT.
5. The screen displays To unpair CAM X,
press the [ZOOM] key at the Parent
Unit.. Press on the parent unit.
6. The screen displays Then, press the
[MENU/SELECT] key to confirm.. Press
SELECT to continue.
7. When unpairing is successful, the screen
displays CAM X is unpaired and returns
to previous menu. If there is no paired
baby unit, the screen displays No CAM is
paired./No link to CAM 1?.The LED light
on the selected baby unit flashes slowly.
General product care
To keep this product working well and looking good,
follow these guidelines:
• Avoid putting it near heating appliances and
devices that generate electrical noise (for
example, motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the baby unit in water and do
not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit is dry before you connect
them to the mains again.
• This baby monitoring system includes a
special lens which is capable of optical zoom
and requires delicate treatment. Please avoid
disassembling, dropping, or any other rough
handling.
Important safety instructions
When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock and injury, including the following:
1. Follow all warnings and instructions marked on
the product.
2. Adult setup is required.
3. This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
4. This product is not intended for use as a medical
monitor.
5. Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in
a wet basement or shower.
6. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can
seriously damage the product.
Baby unit power adapter: Output: 6V DC 600mA
7. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
8. For pluggable equipment, the socket-outlet
shall be installed near the equipment and shall
be easily accessible.
9. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
10. Do not cut off the power adapters to replace them
with other plugs, as this causes a hazardous
situation.
11. Do not allow anything to rest on the power cords.
Do not install this product where the cords may
be walked on or crimped.
12. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home, consult your dealer or local
power company.
13. Do not overload wall outlets or use an extension
cord.
14. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
15. This product should not be placed in any area
where proper ventilation is not provided. Slots
and openings in the back or bottom of this
product are provided for ventilation. To protect
them from overheating, these openings must
not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator
or heat register.
7
8
2
4
5
1
3
6
9
11
10
12
13
14
＜1m (3ft)
＞1m (3ft)