User's Manual
Note
• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be
used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the parent
unit is more than 6.5 feet (2 meters) away from
the baby unit. If you hear any high-pitched
noise, move the parent unit further until the
noise stops. You can also press on the parent
unit to lower or mute the noise.
1. Make sure your baby unit and parent unit are on.
2. Speak towards the microphone of the baby unit.
You will hear the sound at the parent unit, and see
the visual sound indicators light up.
Note
• When the POWER/LINK LED light flashes, move the parent unit closer to the baby unit (observe the
minimum distance of 6.5 feet / 2 meters). You can also check if the baby monitor is connected to a live
power socket and switched on.
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby units.
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of your baby. Never place
or mount the baby unit inside the baby’s crib or playpen.
Note
• To avoid interference from other electronic devices, place your
baby monitor far away from devices such as wireless routers,
microwaves, cell phones and computers.
1. Place the baby units more than 3 feet (1 meter) away
from your baby.
2. Place the parent unit more than 6.5 feet (2 meters)
away from the baby unit to avoid screeching noise.
Caution
• The default volume of your parent unit is Level 3, and the
maximum volume is level 5. If you experience high-pitched
screeching noise
from your baby monitor while positioning:
- Make sure your baby units and parent unit are more than
6.5 feet (2 meter) apart, OR
- Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to 1,500 feet (450 meters) outdoors or 160 feet
(50 meters) indoors. The actual operating range may vary depending on the environmental
conditions and other interferences such as walls, doors and other obstructions.
Frequency control
Crystal controlled PLL synthesizer
Transmit frequency
Baby unit: 1921.536 - 1928.448 MHz
Parent unit: 1921.536 - 1928.448 MHz
Channels
5
Nominal effective
range
Maximum power allowed by FCC and IC. Actual operating range may
vary according to environmental conditions at the time of use.
Power requirements
Baby unit adapter: Input: 100-120V AC 60Hz;
Output: 6V DC @ 400mA
Parent unit adapter: Input: 100-120V AC 60Hz;
Output: 6V DC @ 400mA
Parent unit battery: 2.4V NiMH battery
Technical specifications
Specifications are subject to change without notice.
© 2020 VTech Communications, Inc.
All rights reserved. 10/20. DM1111-X_CIB_V5
DM1111
DM1111-2
Enhanced Range
Digital Audio Monitor
Go to www.vtechphones.com
to register your product for enhanced
warranty support and the latest VTech
product news.
Congratulations
on purchasing your new VTech product. Before using this product, please read Important
safety instructions.
This manual has all the feature operations and troubleshooting necessary to install and
operate your new VTech product. Please review this manual thoroughly to ensure proper
installation and operation of this innovative and feature-rich VTech product.
For support, shopping, and everything new at VTech, visit our website at
www.vtechphones.com.
What’s in the box
Stra
n
gul
at
ion
Hazard
Ke
e
p
this
cor
d
o
ut
of
r
e
ach
o
f
ch
il
d
ren.
T
h
e
cord
n
e
eds
t
o
be
at
l
eas
t
t
h
ree fee
t
a
w
a
y
fr
om
t
h
e
chil
d
at
a
ll
t
im
e
s
.
Do
not
use
w
i
t
h
an
e
xtens
io
n
cor
d
.
Do
n
o
t
r
e
mo
ve
this
t
a
g.
É
l
o
ig
ne
z
ce
c
ord
o
n
d
e
s
enf
a
nt
s
. Le
cordon d
o
i
t se t
r
ou
v
e
r à
a
u m
o
i
n
s tr
oi
s
p
ie
d
s
d’
u
n e
nfa
nt
e
t ce, en to
ut
temps
.
N’
ut
i
li
s
ez p
as
d
e
ra
l
lon
ge.
N
e
r
e
t
i
r
e
z
pa
s
c
e
t
te
é
t
i
q
u
et
te
.
M
an
t
en
ga est
e
c
able f
ue
ra de la alc
a
n
ce
de
l
o
s
ni
ñ
o
s
.
E
s
t
e cable d
e
b
e es
tar p
or
lo men
o
s t
r
es
pi
es
f
uera de la alcanc
e
del n
i
ñ
o
en
t
o
do
m
omento
. N
o lo
u
s
e
con
u
n
a ext
en
s
i
ó
n
i
n
alámbri
c
a.
N
o
qui
t
e
es
t
a eti
quet
a.
Risq
u
e
d’
ét
r
anglem
ent
Riesgo de
e
strang
ula
ción
Stra
n
gulation
Hazard
Ke
e
p
this
cor
d
o
ut
of
r
e
ach
o
f
ch
il
dre
n.
T
h
e
cord
n
e
eds
t
o
be
at
l
e
as
t
t
h
r
ee
fee
t
a
w
a
y
fr
om
t
h
e
chil
d
at
a
ll
t
im
e
s
.
Do
not
use
w
i
t
h
an
e
xtens
io
n
co
r
d
.
Do
n
o
t
r
e
mo
ve
this
t
a
g.
É
l
o
ig
ne
z
ce
c
ord
o
n
d
e
s
enf
a
nt
s
. Le
cordon d
o
i
t se t
r
ou
v
e
r à
au m
o
i
n
s tr
oi
s
p
ie
d
s
d’
u
n e
nfa
nt
e
t ce, en to
ut
temps
.
N’
ut
i
li
s
ez p
as
d
e
ra
l
lon
ge.
N
e
r
et
i
r
e
z
pa
s
c
e
t
te
é
t
i
q
u
et
te
.
M
an
t
en
ga est
e
c
able f
ue
ra de la al
c
a
n
ce
de
l
o
s
n
i
ño
s
.
Es
t
e cable d
e
b
e es
tar p
or
lo
men
o
s t
r
es
pi
es
f
uera de la alcanc
e
del n
i
ñ
o
en
t
o
do
m
omento
. N
o lo
u
s
e
con
u
n
a ext
en
s
i
ó
n
i
n
alámbri
c
a.
N
o
qui
t
e
es
t
a eti
quet
a.
Risq
u
e
d’
ét
r
anglem
ent
Ries
go de
e
s
trang
ula
ción
1 set for DM1111
2 sets for DM1111-2
1
Connect the baby monitor
2
Before use
>6.5ft (2m)
Power on or off the baby unit
• Press and hold until the POWER light
turns on.
• Press and hold until the POWER light
turns off.
Power on or off the parent unit
• Press and hold until the POWER / LINK
light turns on.
• Press and hold until the POWER / LINK
light turns off.
Adjust parent unit speaker volume
The speaker volume is preset to Level 3 on the parent unit. You can adjust to your preferred sound level.
• Press to decrease the volume, and to increase the volume.
Note
• If you continue to press or when the volume reaches the minimum or maximum setting, the parent
unit will beep twice.
To mute the speaker volume
• Press repeatedly until the volume reaches the minimum.
Notes
• When the parent unit is in mute, the visual sound indicator will still indicate the sound detected from the
baby unit.
• To unmute, press repeatedly until it reaches your desired volume.
Turn on or off the audio reminder
With audio reminder feature preset to on, the parent
unit plays an audio reminder when it is connected to
a baby unit. It reminds you to place the baby unit at
least 3 feet (1 meter) away from your baby, and keep
the cords out of the reach of children.
• Press and hold for 8 seconds when the parent
unit is not in use. The visual sound indicators
flashes for 3 times. The audio reminder is disabled.
• Press and hold for 8 seconds when the parent
unit is not in use. The visual sound indicators flashes for 3 times. The audio reminder is enabled.
Notes
• You can press or to adjust or mute the volume when the parent unit is playing the reminder.
• If the speaker volume of the parent unit is turned off, it will resume to the default volume level when the
parent unit plays the reminder.
3
Using the baby monitor
User’s manual
DM1111
DM1111-2
For more support information
S
m
Important safety instructions
The applied nameplate is located at the bottom of the baby
unit’s base.
When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above
2 meters.
4. This product is not a substitute for adult supervision
of the infant. Supervising the infant is the parent’s or
caregiver’s responsibility. This product could cease
operating, and therefore you should not assume it will
continue working properly for any given period of time.
Further, this is not a medical device and should not be
used as such. This product is intended to assist you in
supervising your baby.
5. Do not use this product near water. For example, do not
use it next to a bath tub, wash bowl, kitchen sink, laundry
tub or swimming pool, or in a wet basement or shower.
6. CAUTION: Use only the battery provided. There may be
a risk of explosion if a wrong type of battery is used for
the parent unit. The battery cannot be subjected to high
or low extreme temperature and low air pressure at high
altitude during use, storage or transportation. Disposal of
battery into fire or a hot oven, or mechanically crushing or
cutting or the battery can result in an explosion. Leaving
the battery in an extremely high temperature surrounding
environment can result in an explosion or the leakage of
flammable liquid of gas. Battery subjected to extremely
low air pressure may result in an explosion or the leakage
of flammable liquid or gas. Dispose of used battery
according to the information in The RBRC
®
seal.
7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Power adapter information:
Output: 6V DC 400mA
VTECH TELECOMMUNICATIONS LTD.
Model: VT05UUS06040
Rechargeable battery information:
2xAAA 2.4V 400mAh
YIYANG CORUN BATTERY CO LTD.
Model: NI-MHAAA400×2-FF
8. The power adapters are intended to be correctly oriented
in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
9. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
10. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth
for cleaning.
11. Unplug the power cords before replacing battery.
12. Do not cut off the power adapters to replace them with
other plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply in your home,
consult your dealer or local power company.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
17. This product should not be placed in any area where
proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for
ventilation. To protect them from overheating, these
openings must not be blocked by placing the product
on a soft surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or heat
register.
18. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of any
kind on the product.
19. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorized service facility.
Opening or removing parts of the product other than
specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can
cause electric shock when the product is subsequently
used.
20. You should test the sound reception every time you turn
on the units or move one of the components.
21. Periodically examine all components for damage.
22. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless
telephones, etc. To protect your privacy, make sure the
product has never been used before purchase, reset
the baby monitor periodically by powering off and then
powering on the units, and power off the baby monitor
if you will not use it for some time.
23. Children should be supervised to ensure that they do not
play with the product.
24. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 32
o
F
and 104
o
F.
2. Do not expose the product to extreme cold, heat or
direct sunlight. Do not put the product close to a heating
source.
3. Batteries should not be exposed to excessive heat such as
bright sunshine or fire.
4. Warning—Strangulation Hazard—
Children have STRANGLED in cords. Keep
this cord out of the reach of children (more
than 3 ft (0.9m) away). Do not remove this
tag.
5. Never place the baby unit(s) inside the baby’s crib or
playpen. Never cover the baby unit(s) or parent unit with
anything such as a towel or a blanket.
6. Other electronic products may cause interference
with your baby monitor. Try installing your baby
monitor as far away from these electronic devices
as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions,
personal computers, kitchen appliances and cordless
telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and
implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the
pacemaker.
• Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and
according to the instructions in this user’s manual, the product
is safe to be used based on scientific evidence available today.
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage or
loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers
assume no responsibility for any loss or claims by third parties that may arise through the use
of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Install the parent unit battery
The parent unit runs on rechargeable battery or AC power. To continuously monitor your
baby, make sure you use both battery and AC power at the same time. With the battery
alone, the parent unit can cordlessly run for a short time only.
NOTESNOTE
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible
leakage.
Replace the battery
To replace the battery, press down on the battery compartment cover and pull it out, then
follow the steps above to install the battery.
Connect the baby monitor
NOTESNOTE
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch controlled
electric outlet.
• Connect the power adapters in a vertical or floor mount position
only. The adapters’ prongs are not designed to hold the weight of
baby monitor, so do not connect them to any ceiling, under-the-
table, or cabinet outlets. Otherwise, the adapters may not properly
connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapter
cords are out of reach of children.
• Make sure the POWER light is on after the power plug is fully inserted
into the power jack of the baby unit.
• With audio reminder feature preset to on, the parent unit plays an
audio reminder when it is connected to a baby unit.
Charge the parent unit battery
When you have connected and turned on the baby unit
and all the parent units, they will enter pairing mode
automatically. It takes around 10 minutes for the pairing
process to complete. When the parent unit and baby unit
are successfully paired, both their power LEDs are on
steadily. The baby monitor is ready to use.
NOTESNOTE
• Before using the baby monitor for the first time, charge the parent unit battery for 12 hours.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn
the parent unit off while charging.
• The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.
• The parent unit beeps twice every 10 minutes and the light flashes in red when the battery is low.
Charge the parent unit battery without interruption for at least 30 minutes.
• To keep the battery charged, connect it to AC power when not in use.
Strangulati
o
n
Ha
zar
d
K
eep t
his
c
or
d
out
of
r
eac
h of
c
hi
l
d
r
en
.
T
he cor
d ne
eds
t
o be at
l
e
as
t
t
hr
e
e
f
ee
t
away f
r
om
t
he c
hild at
a
l
l t
imes
.
Do
no
t
u
s
e wi
t
h
a
n e
xt
ens
i
on c
or
d.
D
o not
r
e
mov
e t
his
t
a
g.
É
l
o
i
g
nez
c
e
cor
do
n
d
es
e
nf
a
nt
s
. L
e
c
or
don do
i
t
s
e t
r
ou
ver
à
au moins
tr
oi
s
p
i
e
ds
d’un e
nf
a
nt
e
t
c
e
,
en
t
out
t
e
mps
.
N’
ut
il
is
ez
pa
s
d
e r
a
ll
o
n
ge.
N
e
r
e
t
i
r
ez
p
as
c
et
t
e
é
t
ique
t
t
e.
M
an
t
eng
a es
t
e ca
ble f
u
e
r
a
d
e l
a
a
l
c
anc
e
de los
niños
.
E
s
t
e cab
l
e
d
ebe es
t
a
r
por
l
o
me
nos
t
r
e
s
pies
f
uer
a de la alc
a
nce
del niño en t
odo momen
t
o. No l
o
u
s
e
c
on
u
n
a ex
t
en
s
ión inalámbr
ic
a. N
o
quit
e
e
s
t
a etiquet
a.
Risqu
e
d’étra
nglement
Riesgo
de
est
ra
ngulac
ió
n
Strangulatio
n
Hazar
d
K
e
ep t
his
cor
d
out
of
r
e
ac
h of
c
hil
d
r
e
n
.
T
he c
or
d needs
t
o be at
l
e
as
t
t
hr
ee
f
ee
t
away
f
r
om
t
he c
hild a
t
a
l
l t
imes
.
Do
no
t
u
s
e wi
t
h
a
n
e
xt
e
ns
i
on cor
d.
D
o not
r
e
mov
e
t
his
t
a
g.
É
l
o
i
g
nez
c
e
cor
do
n
d
e
s
e
nf
a
nt
s
. L
e
c
or
don do
i
t
s
e t
r
ou
v
er
à
au moins
t
r
oi
s
p
i
e
ds
d’un e
nf
a
nt
e
t
c
e
,
e
n
t
out
t
e
mps
.
N’
ut
il
is
ez
pa
s
d
e
r
a
ll
o
n
ge
.
N
e
r
e
t
i
r
e
z
p
as
c
et
t
e
é
t
ique
t
t
e.
M
a
n
t
e
ng
a
es
t
e
ca
ble f
u
e
r
a
d
e l
a
a
l
c
a
nc
e
de los
niños
.
E
s
t
e c
a
b
l
e
d
ebe est
a
r
por
l
o
me
nos
t
r
e
s
pies
f
uera de la a
l
ca
nce
de
l niño e
n t
odo mome
n
t
o. No l
o
u
s
e
con
u
n
a e
x
t
e
n
s
ión inalá
mbr
ica
. N
o
quit
e
e
s
t
a etiquet
a.
Risque
d’étra
nglem
ent
Riesgo
de
est
ra
ng
ulac
ión
1
> 3 ft
(1 m)
2
< 6.5 ft (2m)
> 6.5 ft (2m)
1 2 3