User's Manual

Baby monitor lights and tones
Parent unit lights
POWER / LINK POWER / LINK light
• Lights off when the parent unit is off.
• Lights on in green when the parent unit is on and linked to the baby unit.
• Flashes in green when there is no link between the baby unit and parent
unit, or when the parent unit is out of range from the baby unit.
Visual sound indicator
The visual sound indicator has two functions. One is to show the sound level
detected by the baby unit. The other one is to show the volume level during
speaker volume setting.
Sound level detected by the baby unit
• One to three green lights indicate a moderate sound level detected by
the baby unit.
• Additional red lights indicate a higher sound level detected by the baby
unit (e.g. baby crying loudly).
Speaker volume level
• One to three green lights indicate Level 1 to Level 3 of the speaker
volume setting.
• Additional red lights indicate Level 4 to Level 5 of the speaker volume
setting.
Flashes in red when the battery is low.
Parent unit alert tones
Low battery tone • Beeps twice every 10 minutes when the battery is low.
Out of range tone • Beeps three times every 30 seconds when there is no link between the
baby unit and parent unit, or when the parent unit is out of range from
the baby unit.
To keep this product working well and looking good, follow these guidelines:
• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
When you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the adapters
in a cool and dry place.
Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question,
visit our website at www.vtechphones.com, or contact 1 [phone] for customer service.
Why doesn’t the POWER
light on the baby unit turn
on when I switch on the
units?
Perhaps the baby unit is not connected to the power supply.
Connect the baby unit to power supply. The baby unit turns on.
Why doesn’t the POWER
/ LINK light on the parent
unit turn on when I switch
on the units?
Perhaps the battery of the parent unit is depleted and the parent unit is not connected to
power supply. Connect the parent unit to power supply and charge the parent unit battery.
The parent unit turns on and establishes connection with the baby unit.
Why does the baby
monitor not respond
normally?
Try the following (in the order listed) for common cure:
1. Make sure that both baby unit and parent unit are on. Disconnect the power from the
baby unit and the parent unit.
2. Remove the battery from the parent unit.
3. Connect the baby unit to the power supply again. The baby unit turns on.
4. Connect the parent unit to the power supply again. The parent unit turns on.
5. Wait for the parent unit to synchronize with the baby unit. Allow up to one minute for this
to take place.
6. Press or to adjust the speaker volume on the parent unit.
Why does the baby
monitor produce a high-
pitched noise?
The units may be too close to each other. Make sure the parent unit and the baby unit at
least 6.5 feet / 2 meters away from each other.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
Make sure that both baby unit and parent unit are on. If you see the visual sound indicators
light up, but there is no sound, then you may have muted the volume or set it to a lower
level. Adjust the volume to a higher level.
If the visual sound indicators do not light up, and you cannot hear any sound, it is because
the baby sound is too low for the baby unit to detect. This is normal. Place the baby unit at
least 6.5 feet / 2 meters away from your baby.
Why does the parent unit
beep?
The parent unit beeps three times every 30 seconds when the baby unit is out of range. Move
the parent unit closer to the baby unit (but not less than 6.5 feet / 2 meters).
The parent unit beeps twice every 10 minutes and the light flashes in red when the
battery is low. Connect the parent unit to the power supply and charge the battery for at
least 30 minutes.
Why does the parent unit
light flash?
The parent unit beeps twice every 10 minutes and the light flashes in red when the
battery is low. Connect the parent unit to the power supply and charge the battery for at
least 30 minutes.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but not less
than 6.5 feet / 2 meters).
Other electronic products may cause interference with your baby monitor. Try installing your
baby monitor as far away from these electronic devices as possible.
Frequently asked questions
General product care
Storage
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the
holder of a valid proof of purchase (“Consumer” or “you”)
that the Product and all accessories provided in the sales
package (“Product”) are free from defects in material
and workmanship, pursuant to the following terms and
conditions, when installed and used normally and in
accordance with the Product operating instructions. This
limited warranty extends only to the Consumer for Products
purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects
in materials and workmanship during the limited warranty
period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will repair or replace at VTech’s option, without
charge, a Materially Defective Product. If we repair the
Product, we may use new or refurbished replacement parts.
If we choose to replace the Product, we may replace it with
a new or refurbished Product of the same or similar design.
We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option,
is your exclusive remedy. VTech will return the repaired
or replacement Products to you in working condition.
You should expect the repair or replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for
ONE (1) YEAR from the date of purchase. If VTech repairs or
replaces a Materially Defective Product under the terms of
this limited warranty, this limited warranty also applies to the
repaired or replacement Product for a period of either (a)
90 days from the date the repaired or replacement Product
is shipped to you or (b) the time remaining on the original
one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation, fire,
water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration
or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is
caused by signal conditions, network reliability, or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States of America or Canada, or
used for commercial or institutional purposes (including
but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see
item 2 on the following part); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the
unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our
website at www.vtechphones.com or call 1 [phone].
In Canada, go to www.vtechcanada.com or call 1 (800)
267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features may
save you a service call.
Except as provided by applicable law, you assume the risk
of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the
transport of the Product(s) to the service location. VTech
will return repaired or replaced Product under this limited
warranty. Transportation, delivery or handling charges are
prepaid. VTech assumes no risk for damage or loss of the
Product in transit. If the Product failure is not covered by
this limited warranty, or proof of purchase does not meet
the terms of this limited warranty, VTech will notify you and
will request that you authorize the cost of repair prior to any
further repair activity. You must pay for the cost of repair and
return shipping costs for the repair of Products that are not
covered by this limited warranty.
What must you return with the Product to get warranty
service?
1. Return the entire original package and contents including
the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or
oral communications related to this Product. VTech provides
no other warranties for this Product. The warranty exclusively
describes all of VTech’s responsibilities regarding the
Product. There are no other express warranties. No one is
authorized to make modifications to this limited warranty and
you should not rely on any such modification. State/Provincial
Law Rights: This warranty gives you specific legal rights, and
you may also have other rights, which vary from state to state
or province to province.
Limitations: Implied warranties, including those of fitness
for a particular purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/
provinces do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost of
substitute equipment, and claims by third parties) resulting
from the use of this Product. Some states/provinces
do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion
may not apply to you.
Please retain your original sales receipt as proof of
purchase.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with
the FCC criteria. Caution: This Transmitter must be installed to provide a separation distance of at least 20cm from all persons.
The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications
were met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
FCC RF radiation exposure statement
Caution: This baby unit must be installed to provide a separation distance of at least 20cm from all persons. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This baby unit must not be co-located or operating in
conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to
Canada’s Health Code 6 for Exposure of Humans to RF Fields.
For cETL compliance only
Limited warranty
FCC and IC regulations
Operating range
This product operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so,
the baby unit and the parent unit can communicate over only a certain distance - which can vary with the locations of the
baby unit, the parent unit, the weather, and the layout of your home. When the parent unit is out of range, it will beep
three times every 30 seconds and enter searching mode. To improve reception, move closer to the baby unit (but not
less than 6.5 feet / 2 meters).
The RBRC seal
Baby unit overview
1
(On/off)
Press and hold to turn on or off the baby unit.
2 Microphone
3 POWER light
4 Power jack
Parent unit overview
1
Speaker
2
(On/off)
Press and hold to turn on or off the
parent unit.
3
(Volume up)
Press to increase the speaker volume.
4
POWER / LINK light
5
Power jack
6
Visual sound indicator
Indicate the sound level detected by
the baby unit or show the volume level
during speaker volume setting.
7
(Volume down)
• Press to decrease the speaker volume.
• Press repeatedly until the volume
reaches the minimum to mute the
parent unit.
8
(Battery indicator light)
9
Belt clip
10
Battery compartment cover
1
3
4
5
6
7
8
2
9
10
Baby unit light
POWER POWER light
• Lights off when the baby unit is off.
• Lights on in green when the baby unit is on.
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle de
l’unité du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les risques
d’incendie, d’électrocution et de blessures corporelles, dont ceux
qui suivent :
1. Observez toutes les instructions et mises en garde inscrites sur
l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit ne remplace pas la surveillance adulte du
nourrisson. La supervision du nourrisson est la responsabilité
du parent ou de la personne qui s’occupe de l’enfant. Ce
produit pourrait cesser de fonctionner et, par conséquent,
vous ne devriez pas présumer qu’il continuera de fonctionner
correctement pendant une période de temps donnée. De
plus, il ne s’agit pas d’un instrument médical et ne devrait pas
être utilisé comme tel. Ce produit est destiné à vous aider à
superviser votre bébé.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre
source d’humidité, par exemple, près d’une baignoire, cuve
à lessive, évier de cuisine, dans un sous-sol humide ni près
d’une piscine, dans un soussol humide ou une douche.
6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il
existe un risque d’explosion si un autre type de batterie est
utilisé pour l’unité Parents. N’incinérez pas les piles. Celles-
ci risqueraient d’exploser. Jetez les piles usées selon les
renseignements suivant le sceau du RBRC
®
.
7. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la tension serait
inadéquate risque d’endommager sérieusement le produit et
mettre votre sécurité en péril.
Informations sur les adaptateurs électriques :
Sortie : 6V CC 400mA
VTECH TELECOMMUNICATIONS LTD.
Modèle : VT05UUS06040
Informations sur les piles rechargeables :
2xAAA 2.4V 400mAh
YIYANG CORUN BATTERY CO LTD.
Modèle : NI-MHAAA400×2-FF
8. Lorsqu’ils sont branchés dans une prise de courant, les
adaptateurs secteur ont été conçus pour être orientés
correctement, soit à la verticale ou au plancher. Les broches
n’ont pas été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT,
la prise de courant doit être installée près du produit, afin
d’assurer une accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant avant de
procéder au nettoyage. N’utilisez pas de nettoyants en
aérosols. Utilisez un chiffon humide pour le nettoyer.
11. Débranchez les cordons d’alimentation avant de remplacer
le bloc-piles.
12. Ne coupez pas les cordons d’alimentation pour remplacer les
fiches, car ceci peut présenter un danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit
où l’on risque d’écraser le cordon d’alimentation ou de le
piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur l’étiquette. Si vous ne connaissez
pas le type d’alimentation que vous possédez à votre
domicile, consultez votre marchand ou votre compagnie
locale d’électricité.
15. Ne surchargez pas les prises de courant murales ni les
rallonges électriques.
16. Ne placez pas cet appareil sur un chariot, meuble, trépied,
support de montage ni table chancelants.
17. Les trous et ouvertures du boîtier, situés à l’arrière de
l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour
l’empêcher de surchauffer, ne bloquez sous aucun prétexte
ces ouvertures et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou toute autre
surface similaire. De même, ne le positionnez pas à proximité
ni au-dessus d’une source de chaleur ou d’un calorifère. De
plus, ne placez pas l’appareil dans un endroit avant de vous
assurer qu’il y ait une bonne circulation d’air.
18. N’enfoncez jamais d’objets à travers les ouvertures de
cet appareil, car ils pourraient entrer en contact avec
des points de tension dangereux ou causer des courts-
circuits qui peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide dans ce
produit.
19. Afin de réduire les risques d’électrocution, ne démontez
pas cet appareil, mais apportez-le dans un centre de service
autorisé. L’ouverture du boîtier ou le retrait de toutes pièces
que contient cet appareil, à l’exception de l’accès autorisé
à certaines portes ou ouvertures, risque de vous exposer à
des points de tension dangereux ou d’autres dangers. Un
remontage incorrect peut par la suite présenter des risques
d’électrocution.
20. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
21. Examinez les composantes afin de vérifier si celles-ci ne sont
pas endommagées.
22. Il existe un très faible risque de perte de confidentialité
avec certains appareils électroniques (autres écoute-bébés,
téléphones sans fils etc.). Pour l’éviter, s’assurer que le produit
n’a jamais été utilisé avant l’achat, réinitialiser l’unité de façon
périodique, éteindre l’écoute-bébé quand il n’est pas en
cours d’utilisation.
23. Les enfants devraient être supervisés afin de vous assurer
qu’ils ne jouent pas avec l’appareil.
24. Le produit n’est pas conçu pour être utilisé par des personnes
(incluant des enfants) aux capacités physiques, sensorielles
ou mentales réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné suffisamment
de supervision ou d’instructions relativement à l’utilisation de
l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre 0˚ C
(32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez
pas près d’une source de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive
telle que la lumière du soleil ou au feu.
4. Assurez-vous que le moniteur et le
cordon de l’adaptateur sont toujours hors de
portée des enfants, àau moins 1 mètre (3 pieds)
de l’enfant ou du berceau, pour éviter tout
risque de strangulation.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du
parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)
portative avec un article tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des
interférences sur votre moniteur vidéo et audio. Tentez
d’installer votre moniteur vidéo ou audio à l’écart des
appareils électroniques tels que des routeurs sans fil, radios,
téléphones cellulaires, interphones, moniteurs, téléphones,
ordinateurs personnels, électroménagers et téléphones sans
fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans fil
portatifs et les stimulateurs cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à au moins six
pouces du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur
le stimulateur cardiaque, tel que dans une poche de chemise,
lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens
qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se
rapportant aux champs électromagnétiques (EMF) standard. Si vous
le manipulez correctement en suivant les instructions de ce guide,
son utilisation sera sécuritaire pendant de nombreuses années,
selon les meilleures évidences scientifiques dont nous disposons
aujourd’hui.
The RBRC seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating
in an industry program to collect and recycle these batteries at the end of their useful lives, when taken
out of service within the United States and Canada.
The RBRC
®
program provides a convenient alternative to placing used Ni-MH batteries into the trash or
municipal waste, which may be illegal in your area.
VTech’s participation in RBRC
®
makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC
®
program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY
®
for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s
involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
The RBRC seal and 1-800-8-BATTERY® are registered trademarks of Call2recycle, Inc.