User's Manual Part 1

ManualsBrandsVTech Telecommunications ManualsElectronicsCordless Telephone Remote Transceiver

AT&T E2116 (M/B) User manual

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to

reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming

pool).

5. Do not place this product on an unstable surface, such as a table, shelf, or stand. The

product may fall, causing serious damage.

6. Slots and openings in the back or bottom of the base unit and handset are provided for

ventilation. To protect them from overheating, these openings must not be blocked by placing

the product on a soft surface such as a bed, sofa or rug. This product should never be placed

near or over a radiator or heat register. This product should not be placed in any area where

proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the marking

label. If you are not sure of the type of power supply in your home, consult your dealer or

local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where the cord

may have anyone walking on it.

9. Never push objects of any kind into this product through slots in the base or handset as they

may touch dangerous voltage points or short out parts that could result in a risk of fire or

electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take it to an

authorized service facility. Opening or removing parts of the base or handset other than

specified access doors may expose you to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the product is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric

shock.

12. Unplug this product from the wall outlet and refer servicing to an authorized service facility

under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled onto the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions, as improper adjustment of other controls may result in damage and often requires

extensive work by an authorized technician to restore the product to normal operation.

E. If the product has been dropped and the base and/or handset has been damaged.

F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote

risk of electric shock from lightning.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

15. Only put the handset of your telephone next to your ear when it is in normal talk mode.

Before You Begin

Enhanced 2.4GHz Technology - Dual band transmission combines the best of 2.4GHz and

900MHz technologies, providing enhanced performance over standard cordless telephones.

Summary of content (13 pages)

PAGE 1
AT&T E2116 (M/B) User manual Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4.
PAGE 2
Parts Check List 1. 2. 3. 4. 5. 6. 7. 8. Base Unit Handset Base Power Adaptor Telephone Line Cord Battery Belt Clip User’s Manual Wall Mount Bracket To purchase replacement batteries, visit us on the web at www.telephones.att.com or call Advanced American Telephones at 1-800-222-3111. The Handset Layout 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
PAGE 3
e) If the battery is not already charged, place the handset in its base and allow to charge for 10 12 hours (or over-night). After that, be sure to place the handset in its base when not in use to ensure maximum daily performance. 2. If the phone will not be used for long periods of time, remove the battery to prevent possible leakage. NOTE: Install the base unit away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture.
PAGE 4
3. Connect the telephone line cord to the wall jack. 4. Line up the tabs on the wall mount bracket with the slots on the bottom of the base unit. Snap the bracket firmly in place. 5. Mount the base on the wall. Position the base unit so the mounting studs will fit into the holes on the wall mount bracket. Slide the base unit down on the mounting studs until it locks into place. Telephone Operation / CID • While on a call, press to decrease the volume.
PAGE 5
• Press PHONE/FLASH , then press REDIAL/PAUSE. • To delete the last number dialed record, press twice while handset is idle. • While entering numbers, press REDIAL/ PAUSE to insert a dialing pause. PROG • Press to enter programming mode with handset idle (on hook). Base Operation Message Waiting Indicator • If you subscribe to telephone company voice mail with a visual message waiting signal, this light flashes, and MESSAGES WAITING displays on the handset screen when you have voice mail waiting.
PAGE 6
3.After you hang up, the phone automatically returns to pulse service. Message Waiting Your E2116 (M/B) is designed to work with most local and regional telephone service provider's voice messaging systems, providing alerts on both the handset and base unit when new messages come in. Voice messaging is subscription service, available through most service providers, for a monthly fee. Contact your local telephone company for more information.
PAGE 7
Speed Dial Memory You can store up to nine telephone numbers with names (up to 15 characters and 24 digits in each location) into the speed dial memory locations you assign (1 through 9). You can also store telephone numbers with names alphabetically in the directory. See Telephone Directory for instructions. NOTES: • The entries you store in speed dial memory will be marked with 01 through 09 in the telephone directory. • Press (off) at any time to exit memory mode.
PAGE 8
SELECT to move on to edit the number. Use to backspace and make corrections. Press SELECT to move to edit the distinctive ring setting. 4. Press SELECT to save the edited information. Delete a Number/Name Stored in Memory 1. Press and hold the memory location key (1 through 9) of the entry you wish to delete. 2. When the screen displays the entry you want to delete, press SELECT. Then press or ERASE flashes. 3. Press SELECT. The screen displays ERASE NO YES and the number. 4. Press or until YES flashes. 5.
PAGE 9
1. Press . The screen displays DIRECTORY. 2. Press or to scroll alphabetically through the entries stored in the directory. -ORPress the dial pad key for the first letter of the entry you want to edit. 3. When the screen displays the entry you want to edit, press SELECT. Then press or until EDIT flashes. 4. Press SELECT. The screen displays the name and number. The cursor ap-pears at the end of the name. Use , and the dial pad keys to edit the name. Press SELECT to move on to edit the number.
PAGE 10
• The repeat tag (*) in the upper right corner, indicating the party has called more than once. If you answer a call before the information appears on the screen, it will not be in the call history. Review Call History 1. Press (CID) to view call history. 2Use and to scroll through records in call history. NOTE: Press (off) at any time to exit call history. Delete Records from Call History Delete a Specific Call: 1. Locate the record you want to delete from call history. 2. Press DELETE to delete.
PAGE 11
To purchase a headset, visit us on the web at www.telephones.att.com or call Advanced American Telephones at 1-800-222-3111. Once you have a compatible 2.5mm headset, locate the headset jack on the E2116 (M/B) handset. Connect the plug on the headset cord to the jack (under a small rubber flap) on the cordless handset. The plug should fit securely. Do not force the connection. NOTE: Whenever a compatible headset is connected to the cordless handset, the microphone on the handset will be muted.
PAGE 12
• Disconnect your base unit from the telephone jack, and plug in a regular telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company. You hear noise in the Handset, and none of the keys or buttons work • Make sure the power cord is plugged in. Common cure for electronic equipment If the unit does not seem to be responding normally, then try putting the handset in the base.
PAGE 13
Base: 205 gram(without adaptor and wallmount) POWER REQUIREMENTS Handset: 3. 6 V 6 0 0 Base: 9V DC @ 300mA m A h N i - M H B a t t e r y MEMORY Speed Dial: Directory: CID: 9 Memory locations; up to 24 digits, 15 characters per location 20 Memory locations; up to 24 digits, 15 characters per location 45 Memory locations Belt Clip The E2116 (M/B) is also equipped with a detachable belt clip. Align the pins on the inside edge of the clip with the notches on the sides of the handset.