User's Manual

ManualsBrandsVTech Telecommunications ManualsElectronics1.9GHz Cordless Phone

Bluetooth

Add a headset (continued)

The screen will display Adding Headset to device

list... when the base is connecting to your headset.

When a device is successfully connected, the handset

displays Headset A is added and connected to base

and the corresponding status icon ( and 1 or 2).

You hear a conrmation tone. The corresponding light

on the telephone base (D1 or D2) turns on.

If you have trouble pairing your headset, it may be not

compatible with your DS6421. Check the Bluetooth

compatibility list at www.vtechphones.com.

Auto connection

An active device may be disconnected from the telephone base when:

The Bluetooth feature of your cell is turned off.

The power of your device is turned off.

Your Bluetooth device are not in the base’s reachable range.

When the Bluetooth or power on the device is turned on or it moves within

range of the base, the base will try to reconnect to the Bluetooth device. If

you disconnect the device through the device list, the base will not attempt to

reconnect unless your device is moved out of range and back in range again.

10.

•

The pairing process may take up to one minute. If the

pairing process fails, try again.

If you put the handset back in the telephone base or

charger while pairing, the process discontinues and

the handset returns to idle mode.

•

Adding

Headset A

to device

list...

Headset A

is added

and connected

to base.

Summary of content (14 pages)

PAGE 1
Bluetooth Add a headset (continued) 9. The screen will display Adding Headset to device list... when the base is connecting to your headset. 10. When a device is successfully connected, the handset displays Headset A is added and connected to base and the corresponding status icon ( and 1 or 2). You hear a confirmation tone. The corresponding light on the telephone base (D1 or D2) turns on. If you have trouble pairing your headset, it may be not compatible with your DS6421.
PAGE 2
Bluetooth Devices connection Up to four devices can be paired to the telephone base. All paired devices are shown on the device list. To use a paired device, it must be in an active slot (D1 or D2) on the device list and connected. Only one Bluetooth cell phone or a headset can be on a call at a time. Once you have paired a device with the telephone base, you do not need to repeat the pairing procedure again unless you delete the device from the device list.
PAGE 3
Bluetooth Remove a device If you already have the maximum of four paired devices on the device list and you want to add another device, you may first delete a device from the device list. 1. Press MENU on the handset when it is not in use. or to highlight Bluetooth, then 2. Press press SELECT. 3. Press or to highlight Device list, then press SELECT. or to highlight a selected device when 4. Press necessary, then press DELETE. 5. The handset displays Remove Headset A? Press YES to confirm.
PAGE 4
Bluetooth Rename a device You can change the name of a device on the device list. 1. Press MENU on the handset when it is not in use. or to highlight Bluetooth, then 2. Press press SELECT. 3. Press or to highlight Device list, then press SELECT. or to choose a selected device when 4. Press necessary, then press OPTION. 5. Press or to highlight Rename, then press SELECT. The screen displays ENTER NEW NAME. 6. Use the dialing keys to edit the name (page 60). • Press MUTE /DELETE to erase a character.
PAGE 5
Bluetooth Replace an active device If you already have two active devices on the device list and you want to activate a different device, you must deactivate one of the two active device. To replace an active device: 1. Press MENU on the handset when it is not in use. 2. Press or to highlight Bluetooth, then press SELECT. or to highlight Device list, then 3. Press press SELECT. 4. Press or to highlight the device you want to activate, in the bottom two without a prefix D1: or D2: ,then press SELECT.
PAGE 6
Bluetooth Download directory You can download up to four cell phone directories (phonebooks) to your DS6421 telephone system via Bluetooth wireless technology. Each downloaded directory can store up to 1,500 entries with up to 30 digits for each phone number and 15 characters for each name. Before downloading the directory, make sure the cell phone is paired, active and connected to the DS6421. Make sure the handset battery is charged for at least 10 minutes.
PAGE 7
Bluetooth Download directory (continued) • If the selected device’s directory has already been downloaded to DS6421 before, the handset displays the last update date of your cell phone. The directory stored on the DS6421 for that cell phone will be erased and replaced with the current cell phone directory. If you have edited the downloaded entries (page 62), those changes will be lost. Press NEXT to start the download, the screen displays Erasing directory...
PAGE 8
Bluetooth Interruption to directory download If you are downloading a directory from a cell phone and the cell phone receives a call, the download process stops and all handsets display Download fail after the call ends. When you try to view the downloaded directory, the handset displays Last download failed: MM/DD/YY Press SELECT. You need to download the directory again (see page 25). If you are downloading a directory from a cell phone and the telephone base loses power, the download process stops.
PAGE 9
Bluetooth Change PIN You are required to enter a PIN when establishing a Bluetooth connection. The default Pin of your telephone base is 0000. BLUETOOTH Add device Device list Download dir Change PIN To change the PIN: 1. Press MENU on the handset when it is not in use. BACK 2. Press or to highlight Bluetooth, then press SELECT. ENTER 3. Press or to highlight Change PIN, then press SELECT. The handset displays ENTER NEW PIN and the existing PIN. 4. Use the dialing keys to enter a new four-digit code.
PAGE 10
Telephone settings Ringers (handset) In the ringers menu, you can select the ringer tones and adjust the ringer volume for incoming calls to the home and cell lines. Ringer volume (handset) You can adjust the ringer volume for the incoming home and cell calls. To adjust the handset ringer volume: 1. Press MENU on the handset when it is not in use. 2. Press or to highlight Ringers, then press SELECT. 3. Press SELECT to choose Ringer volume. 4.
PAGE 11
Telephone settings Ringer tone You can select the ringer tones for the incoming home and cell calls. To select a ringer tone: 1. Press MENU on the handset when it is not in use. 2. Press or to highlight Ringers, then press SELECT. 3. Press or to highlight Ringer tone, then press SELECT. 4. Press or to highlight All lines, Home, Cell-D1 or Cell-D2, then press SELECT to confirm. 5. Press or to highlight a ringer tone. A sample of each ringer tone plays as you scroll through the choices. 6. Press SET to save.
PAGE 12
Telephone settings Set date/time he answering system announces the day and time of each message prior T to playing it. If you subscribe to caller ID service, the day, month and time are set automatically with each incoming call. However, the year must be correct so that the day of the week can be calculated from the caller ID information. Before using the answering system, set the date and time as follows. To change the setting: 1. Press MENU on the handset when it is not in use. 2.
PAGE 13
Telephone settings Settings In the settings menu, you can change and edit the settings for LCD language, display alerts, CID time sync, rename handset, key tone, dial mode and announce caller ID. LCD language You can select English, Français or Español to be used in all screen displays. To select a language: 1. Press MENU on the handset when it is not in use. 2. Press or to highlight Settings, then press SELECT. 3. Press SELECT to choose LCD language. 4.
PAGE 14
Telephone settings Display alerts In the display alerts menu, you can change and edit the settings for display of alerts on the idle screen. Missed call indicator When there are missed calls that have not been reviewed in the caller ID log, the handsets show XX Missed call(s). If you do not want to review the missed calls one by one, you can reset the SETTINGS missed call indicator. All the entries are then considered LCD language old and kept in the caller ID log.