User's Manual

ManualsBrandsVTech Telecommunications ManualsElectronics1.9GHz Open/Closed Sensor

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor. For

instructions on sensor settings, see the

Abridged user’s manual that came with your

VC7151/VC7152.

You may also view or download the online

User’s manual of VC7151/VC7152 for a full

set of installation and operation instructions

at www.vtechphones.com. In Canada, visit

www.vtechcanada.com.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

Press and hold to enter the

registration mode.

4 – LED light

Red for a second when the sensor is

powered on.

Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

•

Before use

Install batteries to the

open/closed sensor

Press the latch button on the sensor to

open the battery compartment case.

Insert two AAA batteries into the battery

compartment.

NOTES

Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

While you insert the batteries, make sure the

polarities are correct.

The batteries operate properly under the

temperature between -18°C (0°F) and 50°C

(122°F).

Add and register a sensor

Add your new VC7002 open/closed sensor to

your VC7151/VC7152 telephone system.

base before use.

To register a open/closed sensor:

Press and hold /FIND HANDSET on the

telephone base for about 4 seconds until

the IN USE light turns on. The telephone

base shows Registering... Please wait.

Press and hold the pair button on the

open/closed sensor, until the LED light

ﬂashes red, to enter the registration mode.

The telephone base shows Open/Closed X

registered and you hear a beep when the

registration process completes. The

registration process takes about 90 seconds

to complete.

Open/Closed X refers to the sensor’s name.

X refers to the system-assigned number of the

sensor.

•

VC7002

Accessory Open/Closed Sensor

for use with

VTech models VC7151/VC7152

User’s manual

Sensor unit

AAA battery x 2

User’s manual

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Replacing a sensor

If you have purchased this new VC7002

accessory sensor to replace an old sensor,

follow the instructions to deregister your

old sensor. The VC7151/VC7152 telephone

system can support up to 400 sensors.

To replace a sensor, deregister the registered

sensor ﬁrst, and then register this new

sensor to the telephone base.

To deregister a sensor:

Press MENU when the phone is not in

use.

Enter the code *33734# to access the

DEREGISTER menu.

Scroll to Single sensor, and then press

SELECT.

Scroll to the sensor you want to

deregister, and then press SELECT.

Press YES to conﬁrm the deregistration.

The telephone base shows Open/Closed X

is deregistered and you hear a beep when

the deregistration process completes.

To deregister all sensors:

Press MENU when the phone is not in

use.

Enter the code *33734# to access the

DEREGISTER menu.

Press SELECT to select All sensors.

Press YES to conﬁrm the deregistration.

The telephone base shows All sensors are

deregistered and you hear a beep when the

deregistration process completes.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

You will hear an announcement alert

- “Open/Closed X is open”, from the

handset and the telephone base.

The handset and the telephone base

will display Open/Closed X is open,

and then .

The SENSOR light on the telephone

base will turn red.

2. Combine the sensor unit with the magnet

unit.

will disappear from the handset and

the telephone base.

The SENSOR light on the telephone

base will turn off.

•

Test the location for the sensor

You can mount the open/closed sensor on a

door, window, or medicine cabinet that opens

or closes.

1. Take the sensor to the desired mounting

location, and hold at the object and its

respective frame.

2. Open the door, window, or medicine

cabinet and listen for an announcement

alert at your handset and telephone base.

Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength. Move the base closer to the garage,

or move the sensor closer to the base, if the

sensor is out of range.

NOTES

Use adhesive tape to hold the sensor

temporarily whilst testing.

Mount the sensor to a higher position to

avoid obstacles or blockages. Depending on

surroundings and obstructing factors, like walls

or cabinets, the sensor may not transmit to the

base properly.

•

Mount with sticker

1. Attach the sticker C onto the rectangular

area at the rear side of the magnet unit,

2. Stick the magnet unit onto the door.

Mount with sticker

You can choose one out of the four spacers

with suitable height, and then add it to the

magnet unit.

1. Push the spacer towards the magnet unit

until it securely clicks into place.

2. Attach the sticker C onto the rectangular

area at the rear side of the spacer.

3. Stick the magnet unit onto the door.

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

Mount the sensor

We recommend you to mount the magnet unit

on a door, window, or medicine cabinet, and

mount the sensor unit on its respective frame.

NOTES

Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

Make sure you align the magnet unit with

sensor unit when mounting.

The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

The door images in this installation guide are

for conceptual reference only.

TIPS

If there is a difference in level between the door,

window, or medicine cabinet and its respective

frame, or the frame is too narrow or has some

decorative molding, you can choose to mount

the open/closed sensor with spacer. You can

also mount the magnet unit on the frame,

and the sensor unit on the door, window, or

medicine cabinet instead.

You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

•

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

“Open/Closed X*

is open.”

Alerts

Without spacer

Mount the magnet unit

With spacer

Summary of content (2 pages)

PAGE 1
Congratulations Your product package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. Install batteries to the open/closed sensor 1. Press the latch button on the sensor to open the battery compartment case. 2. Insert two AAA batteries into the battery compartment. 1 – Magnet unit 2 – Sensor unit Sensor unit P Accessory Open/Closed Sensor for use with VTech models VC7151/VC7152 on purchasing your new VTech product.
PAGE 2
Mount the sensor unit General product care Without spacer Taking care of your sensor Mount with sticker Your sensor contains sophisticated electronic parts, so it must be treated with care. 1. Attach the sticker B onto the rectangular area at the rear side of the back cover 2. Stick the sensor unit onto the frame. -OR- B Mount with screws 1. Press the latch button on the sensor unit to open the battery compartment case. 2.