User's Manual

Press and then or to choose . Press or to open the submenu. After that,
press or to select to enter PATROL mode to alternately view the image from one
baby unit to the next one in every 10 seconds.
For VM320-2 only
If you are viewing baby unit , the POWER LED light of baby unit turns on.
As baby unit is not being viewed, its POWER LED light flashes.
NOTESNOTE
Note
• If you power on only one baby unit, your parent unit may display and the POWER LED light flashes.
Press and then or to choose . Press or to open the submenu. Press or to select
the baby unit you have powered on.
Status check - Two baby units
Change different views - Patrol
10s
Switch among
the baby units
Press and then or to choose . Press to open the submenu. After that, press
or to select a camera number to enter SINGLE-CAM mode.
Change different views - Single-cam
Use a pencil to mark two holes in parallel.
Make sure they are the same distance apart
as the wall mount holes on the baby unit.
NOTESNOTE
Note
• Check for reception strength and camera
angle before drilling the holes.
Items to purchase
You will need to purchase the
following items separately to mount
your baby unit:
2 screws
2 anchors
Mount the baby unit on dry wall (optional)
Adjust the camera angle.
Drill two holes in the wall.
If you drill the holes into a stud, go to
step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush
with the wall.
Insert the screws into the holes and
tighten the screws until only 1/4 inch
of the screws are exposed.
Align the wall mount holes on the
baby unit with the screws on the wall.
Slide the baby unit down until it locks
into place.
Night vision
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare
on your parent unit screen as the baby unit
is adapting to the dark environment.
• When the infrared LEDs are on, the images
are in black and white. This is normal.
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
colors and backgrounds, the display
resolution may vary. Adjust the baby unit’s
angle or place the baby unit at a higher
level to prevent glare and blurry display.
2
3
4
7
8
9
5
6
1
10
13
12
11
POWER LED light
TALK
Zoom / Back
MENU/SELECT
Arrow keys and
VOL / VOL
Microphone
Battery indicator
Visual sound
indicators
LCD display
Stand
Power jack
Speaker
ON/OFF switch
Overview - Baby unit
Light sensor
Camera
Microphone
POWER LED light
Wall mount holes
Infrared LEDs
ON/OFF switch
Speaker
Power jack
Overview - Parent unit
Sound sensitivity and sound activation
NOTESNOTE
Note
• The types of screws and anchors
you need depend on the
composition of the wall.
63ē
Sound activated screenAdjust sound detection sensitivity
When sound activation is on, the
parent unit screen stays off to save
power when the baby unit detects
no sound.
Once the baby unit detects sounds
that are louder than the chosen
sound sensitivity level, the parent unit screen turns on automatically.
It will then turn off again after 50 seconds of no sound detection.
With sound sensitivity
setting, you can
choose to hear sounds
from the baby unit all
the time, or to hear
sounds that exceed a
certain level.
Parent unit
setting
What
happens...
You may
experience...
What you could do...
Speaker
volume:
Low
Sensitivity:
Highest
[Default]
Hear all
sounds all
the time,
including
background
sounds.
Difficulty in
hearing your
baby’s soft
sounds if the
background
sounds are
louder.
• Increase parent unit’s
speaker volume, and
lower sound sensitivity.
• If you are using a
white noise machine
or sound machine, set
its volume to low, or
relocate it to minimize
background sounds.
Speaker
volume:
MAX
Sensitivity:
Low /
Medium
Only hear
sounds that
exceed the
selected
sound
sensitivity
level.
No sound; or
sounds that
cut in and
out at times
as the baby
unit may not
detect extra
soft sounds.
Increase the sound
sensitivity, and adjust the
volume level if necessary.
For details, please see Adjust the sound sensitivity of the baby
unit in the User’s manual.