User’s manual Digital Audio Baby Monitor Model: BM1000 ht t p: // hk phones.v tec h.
TABLE OF CONTENTS 1. Important safety instructions.............................1 2. SET UP THE baby monitor...........................................4 3. GET TO KNOW the baby monitor...............................7 4. USING YOUR BABY MONITOR........................................11 5. TROUBLESHOOTING.......................................................12 6. TECHNICAL SPECIFICATIONS........................................15 2.1 2.2 2.3 3.1 3.2 3.3 3.4 4.1 4.2 4.3 Package Contents...........
1. Important safety instructions IMPORTANT SAFETY INSTRUCTIONS When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. 4.
15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 17.
Cautions 1. 2. 3. 4. 7. DISPOSAL WARNING 1. 2. 3. When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2002/96/EC. All electrical and electronic products/battery should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
2. SET UP THE baby monitor 2.
2.2 Baby unit installation The baby unit is powered by mains power. To connect the baby unit to the mains power: 1. Choose either power adapter that comes with the package. Insert the DC plug of the power adapter into the DC socket on the side of the baby unit. Connect the other end of the power adapter to a suitable mains power socket. SET UP THE BABY MONITOR 2.
2.3 Parent unit installation The package comes with two rechargeable batteries. You can power up the parent unit by using two rechargeable batteries or by connecting it to the mains power. However, even if the parent unit is connected to the mains power, we recommend you to also install the rechargeble batteries. This guarantees the continual operation in case of a power outage. To set up the parent unit: 1. Remove the battery compartment cover. 2.
3. GET TO KNOW the baby monitor 3.1 Baby unit overview 2 3 1 _ Power indicator On when the baby unit is switched on. 2_ Off when the baby unit is switched off. (On/off) Press and hold to turn on/off the baby unit.
3.2 Parent unit overview 1 2 3 7 4 8 5 6 9 1 _ Sensitivity LEDs 2 _ Power Indicator Light 3 _ Low Battery / Charging Indicator Light 4 _ (Volume down) 5_ Press to decrease the speaker volume. (On/off) Press and hold to turn on or off. 6 _ Speakerphone 7 _ (Volume up) Press to increase the speaker volume.
3.3 Parent unit lights 3 green lights and 2 red lights indicating the sound level detected by the baby unit. Green lights indicate a moderate level of sound is detected. Red lights indicate a higher level of sound is detected. Off when the parent unit is off. On in green steadily when the parent unit is on and is linked to the baby unit. Flashes in green when there is no link between the baby unit and parent unit. On in red steadily when the parent unit is charging. Flashes in red when the battery is low.
3.4 Positioning and operating range 3.4.1 Position the audio monitor Place the parent unit within the operating range of the baby unit. We recommend the parent unit is at least 1.5 metres away from the baby unit to avoid audio feedback. If you still experience audio feedback, move the parent unit and the baby unit farther apart. NOTES • If the signal is poor, try moving the parent and/or the baby unit to different positions in the rooms.
4. USING YOUR BABY MONITOR 4.1 Power the baby unit on or off • Press and hold for 2 seconds to turn on the baby unit. The Power indicator light turns on. • Press and hold for 2 seconds again to turn off the baby unit. The Power indicator light turns off. 4.2 Power the parent unit on or off Press and hold for 2 seconds to turn on the parent unit. The Power indicator light turns on. • Press and hold for 2 seconds again to turn off the parent unit. The Power indicator light turns off. 4.
5. TROUBLESHOOTING If you have difficulty with your audio monitor, please try the suggestions below. My audio monitor does not work at all. • Make sure the baby unit, parent unit and the batteries are installed and charged correctly. For optimum daily performance, charge the parent unit when it is not in use. • Make sure the power adapters are securely plugged into the outlet not controlled by a wall switch. • Make sure the adapter cords are plugged firmly into the baby unit and parent unit.
The parent unit plays any sounds from the baby unit and I think it is too noisy. • You may need to adjust the speaker volume on the parent unit. The parent unit does not play any sound when there is noise from the baby unit. Make sure the parent unit is powered up by connecting it to mains power or to the rechargeable batteries provided. • Make sure the parent unit is turned on and the speaker volume is not set to off. • The parent unit may be too far away from the baby unit.
The battery does not charge in the parent unit or the parent unit battery does not accept charge. • Make sure the batteries are installed in the parent unit battery compartment correctly. The Charging indicator light on the parent unit should be on when charging. • Remove the battery and then install it again, then charge for up to 12 hours. • If the battery is completely depleted, it may take up to 30 minutes to charge the parent unit before it can be used for a short time. • Purchase new batteries.
6. TECHNICAL SPECIFICATIONS No. of channels: 120 Frequency: 1881.792 - 1897.344 MHz Power supply Electrical power: Baby unit: Ten Pao - S004LS0600045 Input: 100 - 240VAC 50/60Hz 150mA Output: 6VDC 450mA Battery Information: Parent unit: GPI - VTHC043C00, 2 x 1.2V AAA size 400mAh NiMH CORUN - Ni-MHAAAJ400, 2 x 1.2V AAA size 400mAh NiMH Transmitting power: Max.
Customer Service Centre Suite 1601, Lever Tech Centre, 69-71 King Yip Street, Kwun Tong, Kowloon, Hong Kong. Customer Service Hotline: (852) 2666 5558 Technical Inquiry Hotline: (852) 2667 7433 VTECH TELECOMMUNCATIONS LTD. A member of THE VTECH GROUP OF COMPANIES. © 2013 VTech Telecommunications Ltd. All Rights Reserved.
