User Manual

For VTech models:
Press and hold /FIND HANDSET on the
telephone base for about four seconds until
the red IN USE light turns on. Then, release
the button.
Immediately place the headset in the
headset charger. It takes about 60 seconds
to complete the registration process. The red
IN USE light on the telephone base turns off.
The ON / OFF light on the headset turns red
when it is registered and charged.
Lift the headset, then press ON / OFF key
on the headset. If you hear a dial tone, the
registration was successful.
For VTech ErisBusinessSystem
TM
:
Press MENU on the console or deskset.
Press or to scroll to Registration, and
press SELECT or /SKIP.
Press or to scroll to select DECT
Headset, and then press SELECT or
/SKIP. The console or deskset screen
displays Registering DECT Headset...(Put
DECT Headset in charger).
Place the headset in the charger. The
registration takes up to 60 seconds to
complete. When the registration is complete,
the console or deskset screen displays
DECT Headset registered.
Lift the headset, then press ON / OFF key
on the headset. If you hear a dial tone, the
registration was successful.
For VTech CM series business phone
system:
Press MENU on the console.
Scroll to Registration, then press SELECT.
Press SELECT again to select Register Ext.
Place the headset in the charger. It may
take up to 60 seconds to complete the
registration. The console shows HDST/SPK
X registered. (X represents the extension
number 9 to 1) and beeps when the
registration is successful.
The console shows Link HDST/SPK X to
extension?. If you want to link the headset
with an extension, scroll to Yes. Otherwise,
choose No and then skip to Step 7. Press
SELECT to confirm.
Scroll to select a desired extension to be
linked with the headset or speakerphone.
Press SELECT to confirm.
Lift the headset, then press ON / OFF key
on the headset. If you hear a dial tone, the
registration was successful. If you linked the
headset with an extension, the extension
screen displays the extension number along
with the line number it is using.
1.
2.
3.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
6.
7.
For AT&T models with
/HANDSET LOCATOR button on the
telephone base:
Press and hold the /HANDSET LOCATOR
button on the telephone base for about four
seconds until the IN USE light turns on, or
the base displays Registering... Please
wait. Then, release the button.
Immediately place the headset in the
headset charger. The ON / OFF light on the
headset flashes quickly and alternately in
red and blue to indicate the registration is in
progress. This may take up to five minutes to
complete. The ON / OFF light on the headset
turns red when it is registered and charged.
You hear a confirmation tone.
Lift the headset, then press ON / OFF key
on the headset. If you hear a dial tone, the
registration was successful.
For AT&T models without
/HANDSET LOCATOR button on the
telephone base:
Press MENU on the telephone base when
idle.
Scroll to Settings, and then press SELECT.
Scroll to Registration, and then press
SELECT. The base displays Registering...
Please wait.
Follow Steps 2 and 3 under For AT&T
models with /HANDSET LOCATOR
button on the telephone base section.
For AT&T Synapse
®
business phone
system:
Press MENU, 2, and then 6 on the telephone
base when idle. Menu Cordless Headset
appears.
Press Register. The base displays
Registering in Progress....
Follow Steps 2 and 3 under For AT&T
models with /HANDSET LOCATOR
button on the telephone base section.
For AT&T Syn248
®
business phone
system:
Press MENU, 2, and then 5 on the
telephone base when idle. Menu Cordless
Headset Registration appears.
Press Register. The base displays
Registering in Progress....
Follow Steps 2 and 3 under For AT&T
models with /HANDSET LOCATOR
button on the telephone base section.
1.
2.
3.
1.
2.
3.
4.
1.
2.
3.
1.
2.
3.
For AT&T SynJ
®
business phone
system:
Press MENU on the telephone base when
idle.
Scroll to Registration, and then press
ENTER twice to select Register HS. The
telephone base shows Registering new
device.... It takes up to 60 seconds to
complete the registration.
Place the headset in the headset charger.
The telephone base shows Cordless
headset registered and beeps when the
registration is successful.
Lift the headset, then press ON / OFF key on
the headset. If you hear a dial tone and the
extension
0
icon also appears on the
telephone base, the registration was
successful. If you have a dial tone but an
extension number other than 0 displays on
the telephone base, the headset is
registered as a handset and will not function
properly. If this is the case, you must
deregister and start over. See Replace a
headset section.
Replace a headset
If you want to replace a headset or reassign
the designated headset number of a registered
headset, you must deregister all handsets
and headsets that are registered to the same
telephone base. Then register each handset and
headset individually.
To deregister all headsets:
To deregister all headsets from the telephone
base, follow the instructions in the user’s manual
of your telephone system, or visit our website
at www.vtechphones.com or AT&T’s website at
www.telephones.att.com.
This operation will deregister all the
DECT handsets, headsets, and cordless
speakerphones, regardless of their battery
status and whether they are within range or
out-of-range.
If the deregistration process is successful, you
hear “Not registered” when you press ON/OFF
key on the headset. If the deregistration fails,
you may need to reset the telephone or headset,
and then try again.
NOTE
You cannot deregister a headset if any system
handset or headset is in use.
To reset:
Unplug the power from the telephone base,
then plug it back in.
1.
2.
3.
4.
•
•
Position the headset
There are four earbuds and four earhooks
provided. One earbud and one earhook have
been attached to the headset.
You can choose a suitable size of earbud,
earhook and an appropriate way to position your
headset.
Replace the pre-installed earbud and
earhook:
Hold both sides of the earbud. Twist and pull
the earbud until it separates from the earpiece.
Rotate the earhook to vertical direction and
then pull the earhook until it separates from the
headset.
Attach a earhook, and then a suitable earbud to
the headset until they fit into place.
To wear on the right ear:
1.
2.
3.
To wear on the left ear:
4. Wrap the earhook with the sponge.
Adjust the headset to wear on the ear:
Hook the headset on your ear. Adjust the angle
of the headset until the microphone is pointing
towards your mouth. Firmly grip the headset
with one hand whenever adjusting the headset
microphone up or down.
•
Over the head band
To attach the head band to the headset:
Refer to Steps 1 and 2 in Replace the
pre-installed earbud and earhook section
to remove the earbud and earhook.
Attach the headset to the headband.
Rotate the headset to horizontal direction until it
clicks into place.
Adjust the head band to fit your head. Adjust
and rotate the angle of the headset until the
microphone is pointing towards your mouth.
1.
2.
3.
4.
To remove the head band from the
headset:
Hold the headset with one hand and the
head band with your other hand.
Rotate the headset to vertical direction and
the pull the headset until it separates form
the head band.
Using the headset
Make a call
Follow the instructions in your telephone
user’s manual for making calls.
Press ON/OFF key to join the call.
Answer a call
Press ON/OFF key to answer a call.
End a call
Press ON/OFF key or place the headset in
the headset charger.
1.
2.
1.
2.
•
•
Ringer
The headset does not have an external ringer.
When there is an incoming call, the headset
earpiece rings.
If you have telephones connected to the same
telephone line, you can rely on the ringers of
those telephones to alert you to incoming calls.
Volume
During a call, press VOL+ or VOL- on the
headset to adjust the listening volume.
Mute
The mute function allows you to hear the other
party but the other party cannot hear you.
During a call, press MUTE. The headset
announced “Mute on”.
Press MUTE again to resume the
conversation. The headset announced
“Mute off”.
Call waiting
When you subscribe to call waiting service from
your telephone service provider, you hear an
alert tone if there is an incoming call while you
are on another call.
Press FLASH to put the current call on hold
and take the new call.
Press FLASH to switch back and forth
between calls.
Multiple headset/handset use
Headset(s) and handset(s) on the same phone
line can join an outside call at the same time.
The number of headset(s) and handset(s) that
can join may be limited by your telephone
system. See your telephone user’s manual for
more information.
To share an outside call:
When a headset or handset is already on a
call, press ON/OFF key on another headset
to join the call.
To exit the call, press ON/OFF key again or
place the headset in the headset charger.
The call continues until all handsets and/or
headsets hang up.
•
1.
2.
•
•
•
•
Intercom call
Follow the instructions in your telephone user’s
manual for initiating an intercom call. When
there is an intercom call request from a cordless
telephone to a headset, the headset earpiece
rings if it is not in use.
To answer an intercom call:
Press ON/OFF key to answer the intercom
call.
To transfer a call to the headset:
During a call on the cordless handset or
telephone base, initiate an intercom call to
the headset. Press ON/OFF key on the
headset to answer the intercom call, and then
hang up the call on the cordless handset or
telephone base.
Operating range
This cordless headset operates with the
maximum power allowed by the Federal
Communications Commission (FCC). Even
so, this headset and telephone base can
communicate over only a certain distance - which
can vary with the locations of the telephone base
and headset, the weather, and the layout of your
home or office.
If there is a call while the headset is out of range,
it may not ring, or if it does ring, the call may not
connect well when you press ON/OFF key on the
headset. Move closer to the telephone base, then
press ON/OFF key on the headset to answer the
call.
If the headset moves out of range during
a telephone conversation, there may be
interference.
To improve reception, move closer to the
telephone base.
•
•
General product care
Taking care of your headset
Your cordless headset contains sophisticated
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the headset down gently. Save the original
packing materials to protect your headset if you
ever need to ship it.
Avoid water
Your headset can be damaged if it gets wet.
Do not use the headset outdoors in the rain,
or handle it with wet hands. Do not install the
headset charger near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your headset
Your headset has a durable plastic casing that
should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Congratulations
on purchasing your new VTech product. Before
using this product, please read Important
safety instructions.
This abridged user’s manual provides you with
basic installation and use instructions. A limited
set of features are described in abbreviated form.
Please refer to the online User’s manual for a full
set of installation and operation instructions at
www.vtechphones.com.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Headset overview
1 – VOL+
• Increase the headset volume.
VOL-
• Decrease the headset volume.
Flash
• While on a call, press and hold to answer
an incoming call when you receive a call
waiting alert.
2 – ON / OFF light
• On when the headset is charging.
ON / OFF key
• Press to answer or end a call.
3 – Microphone
4 – MUTE
Press to activate the voice-controlled
application on your connected cell phone
when idle.
Mute the microphone during a call.
When there is an incoming call, press
to silence the ringer in the earpiece
temporarily.
5 – Earpiece
6 – Earhook
•
•
•
Charger overviewoverview
1 – Magnetic charging mount
• Place the headset for charging.
2 – Power jack
Lights and alert tones overview overview
Light status
Alert tones
Connect
NOTES
Use only the adapters provided.
Charge the battery provided with or identified for
use with this product only in accordance with the
instructions and limitations specified in this manual.
Connect the charger
•
•
Install the battery
Install the battery as shown below.
NOTES
Use only supplied battery.
If the headset will not be used for a long time,
remove the battery to prevent possible leakage.
Charge the battery
Place the headset in the charger to charge. The
LED light turns on.
NOTES
For best performance, keep the headset in the
telephone base or charger when not in use.
The battery is fully charged after 3 hours of
continuous charging.
When fully charged, the battery provides
approximately 4 hours of talk time or 48 hours of
standby time.
•
•
•
•
•
Before use
Add and register a headset
Before use, each newly purchased headset
(IS6200) must be registered to a VTech DS,
IS, LS, or SN series home cordless phone, a
VTech ErisBusinessSystem
TM
or CM series
business phone, an AT&T CL, CRL, CLP,
or TL series home cordless phone, or an
AT&T Synapse
®
, Syn248
®
or SynJ
®
business
phone. Visit www.vtechphones.com for a list of
compatible telephones.
The telephone base recognizes and counts a
headset the same as a handset. You can place
the headset charger anywhere you have an
available power outlet.
Refer to your telephone user’s manual for a
maximum number of headsets that you can
register to the telephone base. If you already
have the maximum number of handsets/
headsets registered, you need to follow the
deregistration information in your telephone
user’s manual before adding a new headset.
Before registering:
Place the non-registered headset in the
headset charger and allow it to charge for at
least 15 minutes before registration. Remove
the headset from the headset charger. The
LED light on the headset flashes slowly and
alternately in red and blue.
To register a headset to a telephone
base:
NOTES
You cannot register a headset if any other system
handset or headset is in use. You can only register
one headset to the telephone base at a time.
The headset must be deregistered before
registering it to another telephone system.
If the registration fails, you hear “Not registered”
when you press ON/OFF key on the headset. The
ON/OFF light on the headset flashes slowly and
alternately in red and blue. To reset the headset,
remove it from the headset charger and then place
it back into its charger. Try the registration process
again.
ErisBusinessSystem™ is a trademark of VTech
Communications, Inc.
Synapse
®
, Syn248
®
and SynJ
®
are trademarks of
Advanced American Telephones.
•
•
•
BC
IS6200
DECT 6.0 accessory
cordless headset
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
Telephones identified with this
logo have reduced noise and
interference when used with
most T-coil equipped hearing
aids and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of the
Telecommunications Industry
Association. Used under license.
User’s manual
Red On when the headset battery is
charging..
Flashes every 10 seconds when
the headset battery is low and
needs charging.
•
•
Blue Flashes twice every three
seconds when the headset is in
use.
Flashes every four seconds when
there is an incoming call.
Flashes every 10 seconds when
the headset is out of the headset
charger and has enough charge.
•
•
•
Red and blue Flashes slowly when the headset
is not registered.
Flashes quickly when the headset
is registering to a telephone base.
•
•
Off No battery is installed, or the
headset has run out of battery.
The headset is powered off.
•
•
T
Compatible with
Hearing Aid T-Coil
TIA-1083
User’s manual
f
d
e
c
b
a
b
a
b
a
One short
beep every
30 seconds
The microphone is muted.•
Two low
beeps
Call waiting alert tone.•
Three rising
beeps
A conference call has started.•