User Guide
Table Of Contents
- IS8151-X_QSG_V6.1_20210709_BW
- IS8151-X_SCB_V2_20210309
- IS8151-X_WEBCIB_V2_210707
- Important safety instructions
- What’s in the box
- Overview
- Connect
- Before use
- Introducing Bluetooth
- Bluetooth setup
- Remote voice control
- Configure your telephone
- Use the handset and telephone base menu
- Set language
- Set date and time
- Set voice language
- Caller ID announce
- Use caller ID to automatically set date and time
- Set speed dial voicemail number
- Voicemail (visual message waiting) indicator
- Clear voicemail indication
- Home area code
- Cell area code
- Dial mode
- Temporary tone dialing
- No line alert
- Cell alert
- Telephone operations
- Make, answer or end a home call
- Call waiting on the home line
- Make, answer or end a cell call
- Call waiting on the cell line
- Answer an incoming cell call while on a home call
- Answer a home call while on a cell call
- Conference home and cell calls
- Handset speakerphone
- Volume
- Silence the ringer
- Mute
- Hold
- Equalizer
- Join a call in progress (for multiple handset models only)
- Chain dialing
- Find handset
- Redial list
- Sound settings
- Intercom
- Call transfer using intercom
- Push-to-talk (PTT)
- Phonebook
- Caller ID
- Review a caller ID log entry
- Memory match
- Missed call indicator
- View dialing options
- Dial a caller ID log entry
- Save a caller ID log entry to the phonebook
- Save a caller ID log entry to the allow list
- Save a caller ID log entry to the block list
- Save a caller ID log entry to the star name list
- Delete the caller ID log entries
- About Smart call blocker
- About the built-in answering system and voicemail service
- Set your built-in answering system
- Answering system and voicemail indicators
- Use the answering machine and voicemail together
- Register a handset
- Screen messages
- General product care
- Frequently asked questions
- The RBRC seal
- FCC, ACTA and IC regulations
- California Energy Commission battery charging testing instructions
- For C-UL compliance only
- Limited warranty
- Disclaimer and Limitation of Liability
- Technical specifications
67
signifies that the Industry Canada technical specifications were
met.
The Ringer Equivalence Number (REN) for this terminal
equipment is 0.1. The REN indicates the maximum number of
devices allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the
RENs of all the devices not exceed five.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
California Energy Commission battery
charging testing instructions
This telephone is set up to comply with the energy-conserving
standards right out of the box. These instructions are intended for
California Energy Commission (CEC) compliance testing only. When
the CEC battery charging testing mode is activated, all telephone
functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power
outlet. Make sure all handsets are plugged with charged batteries
before proceeding.
2. While you press and hold FIND HS, plug the telephone base
power adapter back to the power outlet.
3. After about 20 seconds, when the HOME light starts flashing,
release FIND HS and then press it again within two seconds.
You hear a confirmation tone. The HOME light turns off and all
handsets display To register HS, see manual.. Allow up to one
minute for the process to complete.
N OTE
• When the phone fails to enter this mode, repeat Step 1 through Step 3
above.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power
outlet, then plug it back in. Then the telephone base is powered
up as normal.
2. Register your handsets back to the telephone base. Refer to
Register a handset.