User’s manual Accessory baby unit for use with VTech models VM321/VM321-2 w w w.v t e c h b a b y m o n i t o r s .
Congratulations on purchasing your new VTech product. Before using this product, please read Important safety instructions on page ii of this manual. This manual has instructions on how to set up and pair your new baby unit. For complete instructions on using the baby unit, see the user’s manual that came with your video and audio monitor. If you cannot find the user’s manual, you can view or download it at www.vtechbabymonitors.com. In Canada, visit www.vtechcanada.com.
Important safety instructions When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. 4. This product is not intended for use as a medical monitor. 5.
Important safety instructions (continued) 19. You should test the sound reception every time you turn on the units or move one of the components. 20. Periodically examine all components for damage. 21. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc. 22. Children should be supervised to ensure that they do not play with the product. 23.
Table of contents Getting started.................................................................... 1 Parts checklist....................................................................... 1 Baby unit battery installation................................................. 2 Baby unit installation............................................................. 3 Baby unit installation options................................................. 4 Tabletop to wall mount installation..................................
Getting started Parts checklist Check to make sure the package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. Baby unit Screws (2) * User’s manual User’s manual * Baby unit battery compartment cover * Baby unit power adapter * Wall mount * Wall anchors (2) * Important information Important information * * indicates replacements are available. For more information, visit our website at www.vtechbabymonitors.
Getting started Baby unit battery installation You can power up the baby unit by connecting it to AC power or to four AA alkaline batteries. Even if the baby unit is connected to AC power, we recommend you also install four AA alkaline batteries. This guarantees continual operation in case of a power outage. Install four AA alkaline batteries (not supplied) into the battery compartment, matching the polarity markings (+ and -) inside the battery compartment.
Getting started Baby unit installation Install the baby unit as shown below. Make sure that the power outlet is not controlled by a wall switch. Bundle the power cord neatly with the self-adhesive strap. Power outlet not controlled by a wall switch Raise the antenna for better reception. Baby unit power adapter Self-adhesive strap Baby unit • Use only the baby unit power adapter supplied with this product. To order a replacement, visit our website at www.vtechbabymonitors.com or call 1 (800) 595-9511.
Getting started Baby unit installation options The baby unit is ready for tabletop use. Use the provided wall mount if you want to mount it on a wall. Make sure to test the reception and the baby unit position before completing the wall mounting installation. Tabletop to wall mount installation Option 1: Use this method to fix the wall mount securely on the wall. 1. Place the wall mount on a wall and then use a pencil to mark the top two holes as shown.
Getting started Baby unit installation options (continued) 3. Align the wall mount and screws with the holes in the wall as shown. Make sure to attach the screw in the middle hole first so that the wall mount position is fixed. Then attach the other screw in the top hole. 4. Place the baby unit on the wall mount and tighten the screw into the threaded socket at the bottom to secure the baby unit.
Getting started Baby unit installation options (continued) 5. Bundle the power cord neatly with the self-adhesive strap. Make sure to keep the power adapter cord away from children’s reach.
Getting started Baby unit installation options (continued) Option 2: Use this method so that you can relocate the baby unit with the wall mount easily. 1. Place the wall mount on a wall and then use a pencil to mark the top and the bottom holes as shown. Then remove the wall mount and drill two holes in the wall (7/32” drill bit). Check for reception strength and camera angle before drilling the holes. 2. If you drill the holes into a stud, go to step 3.
Getting started Baby unit installation options (continued) 3. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. 4. Place the baby unit on the wall mount and tighten the screw into the threaded socket at the bottom to secure the baby unit. Align the holes on the wall mount with the screws on the wall and slide the wall mount down until it locks into place.
Getting started Baby unit installation options (continued) 5. Bundle the power cord neatly with the self-adhesive strap. Make sure to keep the power adapter cord away from children’s reach.
Getting started Baby unit overview 5 12 6 1 13 7 2 3 15 8 9 4 14 16 10 11 1 _ Camera 2 _ Infrared LEDs 12 _ Camera angle adjustment tab Tilt to adjust camera angle. 13 _ Speaker Backup light for night vision. 3_ To listen to lullabies. To listen to broadcasts from the parent unit. (On/off) Press and hold to turn on or off. 4 _ Microphone 5 _ Antenna 14 _ Temperature sensor 15 _ Battery compartment cover 6 _ Light sensor 7_ (Play/stop) 16 _ Power jack Press to play lullabies.
Getting started Baby unit lights (On/off) On in red when the baby unit is powered by batteries. On in green when the baby unit is powered by AC power. On in orange when the baby unit is not paired to the parent unit. Flashes in red when the baby unit battery is low. Flashes alternately in red and green when the baby unit is in pairing mode.
Getting started Add and pair a baby unit Each newly purchased baby unit (VM301) must be paired to the parent unit before use. Make sure you power on the baby unit and the parent unit before pairing. To pair a baby unit: 1. On the idle parent unit, press MENU/SELECT. 2. Press or to choose PAIR/UNPAIR CAM, then press MENU/SELECT or . 3. Press MENU/SELECT or again to choose Pair new CAM. 4. Press or to choose a desired baby unit slot, then press MENU/SELECT. 5.
Getting started Unpair a baby unit Make sure you power on the baby unit and the parent unit before unpairing the baby unit. To unpair a baby unit: 1. On the idle parent unit, press MENU/SELECT. 2. Press or to choose PAIR/UNPAIR CAM, then press MENU/SELECT or . 3. Press or to choose Unpair CAM, then press MENU/SELECT or . 4. Press or to choose a desired baby unit, then press MENU/SELECT. 5. Press when the screen displays To unpair CAM # from the system, press [zoom] key. 6.
Appendix Operating range This product operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this baby unit and parent unit can communicate over only a certain distance - which can vary with the locations of the baby unit, the parent unit, the weather, and the layout of your home. When the parent unit is out of range, the parent unit displays Waiting for linking... To improve reception, move closer to the baby unit (but not less than 3 feet).
Appendix Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that: Pacemaker patients • Should keep wireless devices at least six inches from the pacemaker.
Appendix Limited warranty What does this limited warranty cover? The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions.
Appendix Limited warranty (continued) How do you get warranty service? To obtain warranty service in the United States of America, visit www.vtechbabymonitors.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.
Appendix FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation.
Appendix Technical specifications Frequency control Crystal controlled PLL synthesizer Transmit frequency 2402 - 2478.5 MHz Channels 52 Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.
VTECH TELECOMMUNICATIONS LTD. A member of THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 97008. Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W 1L5. VTech is the registered trademark of VTech Holdings Limited. Copyright © 2011 for VTECH TELECOMMUNICATIONS LTD. All rights reserved. Printed in China.