Application Guide

Mount the baby unit on dry wall (optional)
Insert the screws into the holes and tighten
the screws until only 1/4 inch of the screws
are exposed.
Use a pencil to mark two holes in parallel.
Make sure they are the same distance apart
as the wall mount holes on the baby unit.
NOTESNOTE
Note
• Check for reception strength and camera
angle before drilling the holes.
Align the wall mount holes at the bottom
of the baby unit with the screws on the
wall. Slide the baby unit down until it locks
into place.
Adjust the camera angle.
Drill two holes in the wall.
If you drill the holes into a stud, go to
step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush
with the wall.
Dim mode
With dim mode preset to
on, your parent unit display
will dim to conserve energy
after 10 minutes of inactivity,
in which there is neither key
pressed nor alert received
from the baby unit.
10 min inactivity
Press any buttons
NOTESNOTE
• If you do not want LCD to dim automatically, turn off the Dim Mode.
LCD
Brightness
Dim Mode
Dim Mode
On
LCD
Brightness
Dim Mode
Dim Mode
On
Night vision
The baby units have infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare
on your parent unit screen as the baby unit
is adapting to the dark environment.
• When the infrared LEDs are on, the images
are in black and white. This is normal.
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
colors and backgrounds, the video quality
may vary. Adjust the baby units’ angle or
place the baby units at a higher level to
prevent glare and blurry display.
Overview - Baby unit
For VM350-2 only
If you are viewing baby unit , the POWER
LED light of baby unit turns on. As baby
unit is not being viewed, its POWER LED
light flashes.
NOTESNOTE
Note
• If you power on only one baby unit, you may see
the parent unit displaying and then
No link to CAM # (# represents the baby unit
number), and the LINK LED light flashing.
Press VIEW in Single CAM or Patrol mode to switch
to the baby unit you have powered on.
Status check - Two baby units
Select Patrol as your monitoring mode to alternately
view the image from baby units and every 10
seconds.
Change different views - Patrol
10s
Monitoring Mode
Single CAM
Patrol
Split
Select Split as your monitoring mode to view the
images from both baby units at once.
Change different views - Split
Monitoring Mode
Single CAM
Patrol
Split
In Single CAM or Patrol mode, press VIEW to switch
between the image of baby units and .
Change different views - Single CAM
Monitoring Mode
Single CAM
Patrol
Split
Press VIEW
Items to purchase
You will need to purchase the
following items separately to
mount your baby unit:
2 screws
2 anchors
NOTESNOTE
Note
• The types of screws and anchors
you need depend on the
composition of the wall.
Sound sensitivity and sound activation
Sound activationSound sensitivity
When sound activation is on, the parent unit screen stays off
to save power when the baby unit detects no sound.
Once the baby unit detects sounds that are louder than the
chosen sound sensitivity level, the parent unit screen turns
on automatically. It will then turn off again after 50 seconds
of no sound detection.
Sound-activated Screen
On
O
With sound sensitivity setting, you can choose to hear sounds from the
baby unit all the time, or to hear sounds that exceed a certain level. The
default level Highest allows you to hear all sounds (including background
noises).
If you set the sound sensitivity to
a lower level (e.g. Medium), you
will only hear sounds that exceed
the selected level. The baby
unit may not detect soft sounds,
and the parent unit speaker may
remain quiet.
For details, please see Adjust the
sound sensitivity of the baby unit
in the User’s manual.
VOX Sensitivity
Low
Medium
High
Highest
63ē
ON/OFF switch
Speaker
5
Power jack
Light sensor
Camera
Microphone
POWER LED light
Infrared LEDs
Wall mount holes