Installation Instructions

ManualsBrandsVTech ManualsElectronicsBluetooth 5.0 Stereo Audio Module

FCC regulatory compliance statement

§15.19 Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

§15.21 Information to user

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

⚫ List of applicable FCC rules:

47 CFR Part 15, Subpart C 15.203

47 CFR Part 15, Subpart C 15.205

47 CFR Part 15, Subpart C 15.207

47 CFR Part 15, Subpart C 15.209

47 CFR Part 15, Subpart C 15.247

47 CFR Part 2.1093

⚫ Summarize the specific operational use conditions

This module can be used in IOT devices, the input voltage to the module is nominally 3.2-5V.

⚫ Limited module procedures

This module is not a limited module.

⚫ Trace antenna designs

The antenna is not a trace antenna.

⚫ RF exposure considerations

This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with a minimum distance of 20cm between the radiator and your body. This

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

⚫ Antennas

If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class

II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility

through the change in FCC ID (new application) procedure followed by a Class II permissive change application.

⚫ Label and compliance information

Please notice that if the FCC identification number is not visible when the module is installed inside another device,

then the outside of the device into which the module is installed must also display a label referring to the enclosed

module. This exterior label can use wording such as the following: “Contains FCC ID: 2AZ2A-VTBMA01” any similar

wording that expresses the same meaning may be used.

§ 15.19 Labelling requirements shall be complied on end user device.

Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant KDB publications. For E-label,

please refer to §2.935.

⚫ Information on test modes and additional testing requirements

The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install

module.

The module is limited to installation in mobile application, a separate approval is required for all other operating

configurations, including portable configurations with respect to §2.1093 and difference antenna configurations.

Summary of content (5 pages)

PAGE 1
FCC regulatory compliance statement §15.19 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §15.21 Information to user Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 2
Test software access to different test modes: Bluetooth test 3 (V2.6) Testing item, Frequencies, Transmit Power, Modulation Type can be selected on the test script instructions.
PAGE 3
⚫ FCC other Parts, Part 15B Compliance Requirements for Host product manufacturer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements.
PAGE 4
===================================================== ISED compliance statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 5
indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. a list of all antenna types PCB Antenna 1.73dBi Dipole Antenna -1.