INSTALLATION & OPERATION MANUAL V SERIES FOOD HOLDING AND TRANSPORTATION CABINETS AND BANQUET CARTS MODELS VHP3 VHP7 VHP8 VHP15 VHP20 VBP5I VBP7I VBP13I VBP15I VBP77I ML-126343 ML-126344 ML-126345 ML-126346 ML-126347 ML-138030 ML-126358 ML-126359 ML-126360 ML-126361 VBS7 VBS15 VHDP5 VDW3 VB90 VB96 VB150 VB200 ML-138032 ML-138033 ML-138035 ML-138036 ML-126548 ML-126550 ML-126552 ML-138034 For additional information on Vulcan-Hart or to locate an authorized parts and service provider in your area, visit
V SERIES IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. WARNING IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.
V SERIES INSTALLATION, OPERATION AND CARE V SERIES FOOD HOLDING AND TRANSPORTATION CABINETS AND BANQUET CARTS SAVE THESE INSTRUCTIONS FOR FUTURE USE Model VBP77I cabinets have individual controls (Fig. 1) for each of the two compartments. The operator is able to hold two different products at two different temperatures in separate sections of the same cabinet. Vulcan-Hart Holding and Transport Cabinets and Banquet Carts are produced with quality workmanship and material.
V SERIES INSTALLATION Before installing, verify the electrical service agrees with the specifications on the rating plate located on the lower rear of the cart. If the electrical service does not agree with the rating plate, do not proceed with installation. Contact your dealer or local Vulcan-Hart service technician immediately. 4. On food holding and transport cabinets, remove cardboard element cover protector from cabinet bottom. Remove adjustable tray slides from box.
V SERIES ELECTRICAL CONNECTIONS INSTALLATION CODES AND STANDARDS Electrical and grounding connections must comply with the applicable portions ofthe National Electrical code and/or other local electrical codes. The APPLIANCE must be installed in accordance with: In the United States of America: 1. State and local codes. The cord and plug supplied, is a suitable durable cord with molded plug and is provided with a proper strain relief. 2. National Electrical Code, ANSI/NFPA-70 (latest edition).
V SERIES Electrical Connection Disconnect electrical power to the machine and follow Lockout/ Tagout procedures before cleaning. Electrical and grounding connections must comply with the applicable portions of the National Electrical Code and/or other Local Electrical Codes. MODEL VOLTAGE AMP PHASE HZ NEMA PLUG VBP5I, VBP7I, VBP13I, VBP15I, VBS7, VBS15, VHDP5, VDW3 110/120 208/240 10 5.4 1 60 5-15 6-15 VBP77I 110/120 208/240 20 10.9 1 60 5-20 6-20 VHP3, VHP7, VHP8 110/120 208/240 5 2.
V SERIES OPERATION BEFORE FIRST USE The cabinet and its parts are hot, be very careful when operating, cleaning or servicing the cabinet. Disconnect electrical power to the machine and follow Lockout/ Tagout procedures before cleaning. CONTROLS POWER INDICATOR LIGHT 160 170 1 80 150 60 20 0 80 90 100 210 80 20 70 NSF® 105 °C °F 22 0 60 200 50 40 2 1 190 0 14 100 12 0 FULL RANGE THERMOSTAT THERMOMETER 3 4 5 6 7 8 9 10 POWER/HEAT OFF HEAT INDICATOR LIGHT Fig.
V SERIES OPERATING APPLIANCE 1. Connect electric power supply. 80 90 100 210 80 20 70 NSF® 105 60 0 °C °F 20 PO 22 0 50 40 60 200 100 12 0 Power indicator light is lit. 190 • 160 170 1 80 150 0 14 Fig. 8 4. Once desired temperature is reached, heating elements will cycle on and off. • 5. Temperature in heated appliance will fluctuate as the heating elements cycle on and off. Fig. 6 2. Turn thermostat knob to desired setting. • Heating elements begin heating.
V SERIES CLEANING Shutdown Disconnect electrical power to the machine and follow Lockout/ Tagout procedures before cleaning. Turn full range thermostat counterclockwise to OFF. 2 1 3 4 5 6 7 8 9 10 Clean appliance interior with mild soap and water whenever a food spill occurs. Never use harsh chemicals or abrasive pads to clean appliance. EAT OFF Daily 1. Allow appliance to cool before cleaning. Fig. 9 2. Remove tray slides or plate racks and clean in a sink as you would any utensil.
V SERIES TROUBLESHOOTING SYMPTOMS POSSIBLE CAUSES REMEDY Temperature incorrect No main power source Check the power source or circuit breaker. Power switch in off position Press power switch to the on position. Door open Close door. Door leaks Damaged door gasket Check door gasket for damage. If adjustment is needed, contact your Authorized Vulcan-Hart Servicer. Compartment does not heat properly Defective heating coil Contact your authorized service provider.
V SERIES WIRING DIAGRAMS THERMOSTAT POWER POWER A A R BLACK POWER CONNECTION 120V, 1PH, 60 Hz 208/240V, 1PH, 60 Hz BLACK WHITE RED WHITE GREEN HEATING ELEMENT HEATING ELEMENT VB48, VB72, VB90, VB96, VB150, VBP5I, VBP7I, VBP13I, VBP15I, VHP15, VHP20 Wiring Diagram — 11 —
V SERIES POWER CONNECTION 120V, 1PH, 60 Hz 208/240V, 1PH, 60 Hz BLACK BLACK WHITE POWER POWER R A POWER POWER R A GREEN THERMOSTAT HEATING ELEMENT BLACK THERMOSTAT HEATING ELEMENT VBP77I Wiring Diagram — 12 —
V SERIES THERMOSTAT POWER CONNECTION 120V, 1PH, 60 Hz 208/240V, 1PH, 60 Hz POWER A A RED BLACK WHITE WHITE GREEN HEATING ELEMENT VHP3, VHP7, VHP8 Wiring Diagram — 13 —
V SERIES VULCAN REPLACEMENT PARTS LIST BOLT, RETAINING RACK (PACK OF 4) CAP, CHROME INSPECTION CLIP, ELEMENT CORD, POWER 12/3 120V. 15 AMP CORD, POWER 12/3 120V. 20 AMP CORD, POWER 12/3 208/240V. 15 AMP CORD, POWER 16/3 120V. ELEMENT, 120V – 1000W ELEMENT, 120V – 600W (1220/1826) ELEMENT, 208/240V – 600W (1220/1826) ELEMENT, 208/240V – 1000W (1826-40) GASKET, DOOR HANDLE, PUSH/PULL HANDLE, PUSH/PULL S.S. (2026 SERIES) HANDLE, PUSH/PULL S.S. (2-90 ONLY) HANDLE, PUSH/PULL S.S.
V SERIES NOTES (9-07) — 15 — PRINTED IN U.S.A.
V SERIES SERVICE AND PARTS INFORMATION To obtain service and parts information concerning this model, contact the Vulcan-Hart Service Agency in your area (refer to our website, www.vulcanhart.com for a complete listing of Authorized Service and Parts depots). When calling for service, the following information must be available: model number, serial number, manufacture date (MD) and voltage.