INSTALLATION & OPERATION MANUAL VCD SERIES CHIP WARMERS MODELS: VCD22* VCD44 ML-138037 ML-138069 *Formerly VCD5 For additional information on Vulcan-Hart or to locate an authorized parts and service provider in your area, visit our website at www.vulcanhart.com VULCAN-HART DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC www.vulcanhart.com Vulcan ©2010 All Rights Reserved 3600 NORTH POINT BLVD.
VCD SERIES CHIP WARMER F-38053 (09-10) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD STARTUP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITYOF THIS OR ANY OTHER APPLIANCE. Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
VCD SERIES CHIP WARMER F-38053 (09-10) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCD SERIES CHIP WARMER F-38053 (09-10) GENERAL If the warmer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. INTRODUCTION Vulcan-Hart Chip Warmers are produced with quality workmanship and material. Proper installation, usage, and maintenance of your warmer will result in many years of satisfactory performance. Carefully unpack warmer and place in a work accessible area.
VCD SERIES CHIP WARMER F-38053 (09-10) ACCESS PANEL POSITIONING: SCOOP HOLDER INSTALLATION: 1. The Chip Scoop Holder will secure up to a 6“ wide scoop. 2. Ensure that top Baffle notches are over carriage bolts. Insert Access Panel onto the back of the Chip Warmer. (Fig. 1) 1. 2. On either the left or right side of the Chip Warmer, loosen four side screws one revolution. Position the Chip Scoop Holder. (Fig. 3) (Fig. 1) 3. On both sides of Access Panel, place clips into slots, then lock. (Fig.
VCD SERIES CHIP WARMER F-38053 (09-10) All warmers are equipped with a three-prong plug. It is imperative that this plug must be connected into a properly grounded three-prong receptacle. If the receptacle is not the proper grounding type, contact an electrician. Do not remove the grounding prong from this plug. ELECTRICAL REQUIREMENTS ELECTRICAL CODES & STANDARDS: The warmer must accordance with: be installed in In the United States of America: 1. State and Local Codes. 2.
VCD SERIES CHIP WARMER F-38053 (09-10) OPERATION BEFORE FIRST USE TESTING THE CHIP WARMER The Chip Warmer should be thoroughly cleaned before initial use. The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. Always disconnect electrical power to the Chip Warmer before cleaning or servicing. 1. Remove Access unlocking clips. Panel Before using the Chip Warmer for the first time, verify that it operates properly. by 2.
VCD SERIES CHIP WARMER F-38053 (09-10) OPERATION INSTRUCTIONS SHUTDOWN The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. 1. At the end of the day, switch Power Switch to OFF position. Follow cleaning instructions in this manual, if necessary. 2. 3. Switch Power Switch to ON position. Verify that switch illuminates. Open Top Door.
VCD SERIES CHIP WARMER F-38053 (09-10) MAINTENANCE EXTERIOR: Refer to “STAINLESS STEEL CARE.” CLEANING The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. electrical cleaning. Always power supply HEAVY-DUTY CLEANING: For heavy-duty cleaning, use warm water, a degreaser, and a plastic, stainless steel, or Scotch-Brite pad. Never rub in a circular motion -- rub gently in the direction of the steel grain. Always rinse thoroughly.
VCD SERIES CHIP WARMER 4. Never rub in a circular motion. Always rub gently in the direction of the steel grain. 5. Never leave any food products or salt on the surface. Many foods are acidic. Salt contains chloride. F-38053 (09-10) If signs of breakdown appear, restore the stainless steel surface. First, thoroughly clean, rinse, and dry the surface. Then, on a daily basis, apply a high-quality stainless steel polish according to manufacturer’s instructions.
VCD SERIES CHIP WARMER F-38053 (09-10) TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE REMEDY Chip Warmer not operating Chip Warmer not plugged into power source. Lighted power switch not in ON position. Plug chip warmer into correct power source as indicated on serial data plate. Press power switch to ON position. Check fuse and reset is necessary. Check GFCI switch on outlet. No power. GFCI or Ground Fault Circuit Indicator tripped. Moisture problem. Dry moisture problem.
VCD SERIES CHIP WARMER F-38053 (09-10) WIRING DIAGRAM VCD22 & VCD44 11
