INSTALLATION & OPERATION MANUAL ROUND ELECTRIC TILTING SKILLET MODEL VETRS35 MODEL VETRS35 VULCAN-HART FORM 31036 (4-98) ML-114826 COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL.
TABLE OF CONTENTS GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Location . . . . . . . . . . . . . . . . . . . . . .
Installation, Operation and Care of ROUND ELECTRIC TILTING SKILLET MODEL VETRS35 PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Your Vulcan-Hart Round Tilting Skillet is a versatile piece of equipment. It allows you to stew, simmer, pan fry, braise, grill, or saute, and all with a very uniform heat pattern. Capacity of Model VETRS35 is 35 gallons. Vulcan-Hart tilting skillets are produced with quality workmanship and material.
INSTALLATION CODES AND STANDARDS The tilting skillet must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. In Canada: 1. Local codes. 2. Canadian Electrical Code, Part 2, CSA Standard C22.1 (latest edition). Copies may be obtained from The Canadian Standard Association, 178 Rexdale Blvd.
1. Remove the control box cover plate. Mount suitable 123⁄32" (43.6mm) conduit fitting in knockout opening. 2. Connect field wire to the terminal block as indicated on the wiring diagram. The wiring diagram is located inside the wiring compartment at the rear of the tilting skillet. Wire must be of the type suitable for 90°C service. 3. After making the connections, replace the control box cover plate. 4.
OPERATION WARNING: THE TILTING SKILLET AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE TILTING SKILLET. CONTROLS (Fig. 1) POWER SWITCH INDICATOR LIGHT THERMOSTAT PL-41025-1 Fig. 1 Thermostat — Maintains set temperature by controlling power supply. Power Switch — Turns power to the skillet ON and OFF. Indicator Light — When lit, indicates the heating elements are supplying heat to the skillet. Hand Wheel — (Not Shown.
To prevent discoloration of stainless steel cooking surface, do not turn the heat on unless the skillet is covered with a fluid, a thin layer of cooking oil, or food to be cooked. 1. Tilt skillet to ensure that it moves easily. Turn handle as far as it will go and then return to upright position. 2. Turn the Power Switch ON. 3. Set the Thermostat dial to HIGH (#10). 4. Preheat skillet and allow it to cycle in order to equalize heat across the entire pan surface. 5.
Once A Day Thoroughly clean the skillet with warm water and a mild detergent. Rinse thoroughly and wipe dry with a soft clean cloth. Stainless Steel Clean stainless steel surfaces with a damp cloth and polish with a soft dry cloth. To remove discolorations, use a non-abrasive cleaner. MAINTENANCE WARNING: THE TILTING SKILLET AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE TILTING SKILLET.
