Operation Manual

ManualsBrandsVW ManualsVehicleRNS510 - 2011

RNS 510

User manual

LAST UPDATED : 2011.11.16

compatible with VW car models with RNS510

Car-Solutions.com

Summary of content (14 pages)

PAGE 1
m co LAST UPDATED : 2011.11.16 io ns .
PAGE 2
m Contents Main specification Features System diagram Components Exterior io ns . 1.1 1.2 1.3 1.4 1.5 co 1. Before the installation DIP switch KEYPAD Factory mode Rear parking guide line OSD (on screen display) 8 9 10 11 13 14 C ar 3. Troubleshooting -S 2.1 2.2 2.3 2.4 2.5 ol ut 2.
PAGE 3
co Spec. (VIDEO INTERFACE) A/V Input (Rear video source) CVBS(Rear camera) Input (Rear camera source) Analog RGB Input (Navigation System output) LCD Input (Car system Input) io ns . 1. Input -3x -1x -1x -1x m 1.1 Main specification 2. Output Spec. - 1 x LCD Output (LCD operation) - 4 x Audio Select (12V power comes out from 4 wires of cable by video, Navigation mode) ol ut 3. Power Spec. - Input power : 10VDC ~ 16VDC - Power consumption : 6WATT in maximum level C ar -S 4.
PAGE 4
m 1.2 Features co  Clear high definition screen io ns .
PAGE 5
Switch for source toggle co Keypad m 1.3 System diagram MCU NAVIGATION Input (Analog RGB) io ns .
PAGE 6
Sub board * 1pc. Extension cable * 2pc. Button cable * 1pc. FFC cable * 2pc. io ns . FPC cable * 1pc. co m 1.4 Components (FPCABL0011) TOUCH cable * 1pc. ol ut (HTOUCH0003) POWER cable (10P) * 1pc. (HPOWER0005) -S LVDS cable * 1pc. (HLVDSC0006) C (HARETC0001) ar Mode cable * 1pc. RGB cable * 1pc. (HNAVIC0002) (QCPASS0041) (HBUTTO0003) IR cable (8P) * 1pc. (HIRCAB0003) (HTOUCH0001) (HTOUCH0002) (FFCABL0006) Ground cable * 1pc. OR (HGROUN0001) Keypad * 1pc. AV cable * 1pc.
PAGE 7
⑥ ⑦ ⑧ co ⑤ m 1.5 Exterior Product dimension ⑥ ⑤ io ns .
PAGE 8
RGB INPUT skip ON : RGB mode OFF OFF : RGB Display A/V 1 skip ON : A/V1 mode OFF OFF : A/V1 Display 3 A/V 2 skip ON : A/V2 mode OFF OFF : A/V2 Display 4 A/V 3 skip ON : A/V3 mode OFF OFF : A/V3 Display NOT USED 6 NOT USED - Input mode use : A/V2, A/V3 - Use original navigation ▷ ▷ ▷ ▷ ▷ DIP DIP DIP DIP DIP S/W S/W S/W S/W S/W : : : : : 1,2  ON (INPUT MODE SKIP) 3  OFF (enable A/V2) 4  OFF (enable A/V3) 5, 6, 7  OFF 8  ON ON : REAR CAMERA mode ON OFF : MAIN rear camera ar Rear mode S
PAGE 9
m 2.2 KEYPAD Key ol ut io ns . co ※ FACTORY MODE (Interface setting) : Press “UP” button about 2 seconds long and you will approach FACTORY mode. Also you can get there in pressing these keys in this sequence; “UP” → “DOWN” → “UP” → “MENU” MENU/EXIT Implement OSD screen SEL/INPUT Selection -S Move downward, if you press about 2 seconds long, you are able to reset the factory mode. ar DOWN Move upward, if you press about 2 seconds long, you are able to approach the FACTORY mode.
PAGE 10
m 2.3 Factory mode IMAGE PARK UTIL - PARK ENABLE : able to choose whether the rear guide line is displayed or not with rear gear. (default-ON) -PARK SETUP : able to adjust the position of the rear guide line with the keypad. - SAFE ENABLE : The function that forbids drivers to change the LCD to DVD or A/V while driving. User returns to the main screen by this function. (Default : off) ( Refer to the page#11 ) - NAVI SELECT (N.
PAGE 11
m 2.4 Rear parking guide line ※ FACTORY mode – Press “UP” button on the keypad long about 2 seconds. ② If you press “UP” button on the keypad about 2 seconds long, you can see the left image on the screen. Now that you choose “PARK SETUP” and press “OK” on the keypad, you can control the width of the rear parking guide line. C ar -S ol ut io ns . co ① Once you change up into rear gear, the rear parking guide line will automatically appear on the screen like the left picture.
PAGE 12
m 2.4 Rear parking guide line io ns . ~ co ※ FACTORY default -Types:0, H_Pos:50, V_Pos:120 level 0 level 4 C ar -S ol ut ③ The width of the rear parking guide line has 5 level(0~4). After you control the level with “UP”, “DOWN” button on the keypad, you can move to the horizontal positioning mode after pressing “SEL” button and saving process. ( The current state is displayed right-top.
PAGE 13
m 2.5 OSD (on screen display) io ns . co ※ OSD : Press “MENU” button on the keypad.
PAGE 14
m 3. Troubleshooting co Q. I can not switch A/V sources. A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable. io ns . Q. All I got on the screen is black. A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well. (Second lamp indicates AV sources connected works well.) Check interface connection has been done well. Q. Displayed image color is not proper. (too dim or not suitable color) A.