User`s manual

VXI Technology, Inc.
48 Tektronix to VXI Technology Cross-Ref. Guide
INTERFACING TO THE MODULE
The SM4350 has two, 160-pin high density DIN connectors on its front panel for I/O interfacing.
Mating connector and pin part numbers are referenced below. These parts can be ordered directly
from VXI Technology or the manufacturer listed in the table.
ACCESSORIES
52-0236-000: Connector Kit (Includes 160 Pin Connector & Retaining Hardware)
Desc: Connector Kit Mfgr.: VXI Tech. Mfgr P/N: 52-0236-000 Contact Info: 949-955-1VXI/www.vxitech.com
Desc: Connector Mfgr.: ERNI Mfgr P/N: 024070 Contact Info: 804-530-5012/www.ernicomponents.com
Desc: Retaining Hardware Mfgr.: VXI Tech. Mfgr P/N: 41-0298-000 Contact Info: 949-955-1VXI/www.vxitech.com
52-0237-000: Strain Relief Brackets
Desc: Strain Relief Brackets Mfgr.: VXI Tech. Mfgr P/N: 52-0237-000 Contact Info: 949-955-1VXI/www.vxitech.com
52-0110-000: 10-Pin Cable Assembly
Desc: 6 ft. 24GA Teflon, 10 Crimp Pins Mfgr.: VXI Tech. Mfgr P/N: 52-0110-000 Contact Info: 949-955-1VXI/www.vxitech.com
52-0235-000: Floating Wire Shroud (Does Not Include Connector Pins)
Desc: Floating Wire Shroud Mfgr.: VXI Tech. Mfgr P/N: 52-0235-000 Contact Info: 949-955-1VXI/www.vxitech.com
52-0109-001: Crimp Pins (500 per Reel)
Desc: Crimp Pins Mfgr.: ERNI Mfgr P/N: 014729 Contact Info: 804-530-5012/www.ernicomponents.com
52-0109-000: Lose Crimp Pins (100 per Bag)
Desc: Lose Crimp Pins Mfgr.: VXI Tech. Mfgr P/N: 52-0109-000 Contact Info: 949-955-1VXI/www.vxitech.com
46-0010-000: Crimp Tool
Desc: Crimp Tool Mfgr.: ERNI Mfgr P/N: 014374 Contact Info: 804-530-5012/www.ernicomponents.com
46-0011-000: Extraction Tool
Desc: Extraction Tool Mfgr.: ERNI Mfgr P/N: 471555 Contact Info: 804-530-5012/www.ernicomponents.com
The single floating wire shroud assembly is used to provide added strain relief. Refer to figure
below.
In many ATE applications, a termination panel for the instrumentation is utilized. This termination
panel will have connectors that mate to the UUT or an intermediate test fixture. A termination
panel may take the form of an Interconnect Assembly (ICA) made by manufacturers such as
Virginia Panel or Macpanel. In either case, it is desirable to maintain the same I/O layout at the
panel to avoid costly redesign of test fixturing or UUT cable assemblies.
VXI Technology offers a couple of options that prevent the need for any interface panel to UUT
redesign as follows:
• wired funnel assemblies that mate directly to the SM4350 front panel
• custom cabling between SM4350 front panel and ICA/termination panel
For customers who plan on developing their own cabling between the SM4350 and the
termination panel, this section provides a cross-reference pinout table between the VX4350 and
the SM4350 in Table 6-1 and Table 6-2.
160-pin mating
connector
Cable Access
Single Floating Wire Shroud