B200 Wireless Headset System
VXI. Connecting people to a digital world. Table of Contents Box Contents......................................................................................4 Basic Safety Instructions......................................................................5 Product Features................................................................................. 6 Glossary of Terms............................................................................... 8 Operation Summary.....................................
BOX CONTENTS 5 1. T-cord (for office phones other than Cisco) 2. Patch cord (for Cisco phones- models 7940 or higher)* 1 3. AC adapter 4. Cord wraps 2 5. B200 base 6. B200 headset 3 6 4 Also included (not shown) User Guide Quick Start Card BASIC SAFETY INSTRUCTIONS CAUTION Danger of explosion if battery incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
PRODUCT FEATURES BlueParrott B200 Headset PRODUCT FEATURES BlueParrott B200 Base Pairing button Headset charge contact Adjustable headband Standby/pairing indicator lights Headset indicator light T-cord or Patch cord T-bar Multi-function button with indicator lights Noise canceling microphone Microphone volume Handset indicator light Volume (increase)/Mute control Volume (decrease) 6 AC adapter 7
GLOSSARY OF TERMS Standby Mode – Headset is active, but not on a call. Standby time is up to 100 hrs. on a full charge. Standby Mode is automatic when removing headset from the base. Turning off the headset while it is out of the base takes it out of Standby Mode. Talk Time – Actual time spent on a phone call. Talk TIme equals 6 hrs. on a full charge. Pair / Pairing – Pairing is a simple and quick procedure that enables one Bluetooth product to communicate with another Bluetooth product.
A: For phones without headset ports INSTALLATION A: Phones without headset ports B : For phones with headset ports STEP 1: Disconnect the handset cord from your telephone’s base. STEP 2: Plug short end of T-cord into the now empty handset port on your phone. STEP 3: Plug the other (longer) end of the T-cord into the port on the B200 base marked Phone . Thread cord under the hooks on the base. STEP 4: Plug the handset into the port on the T-cord.
CHARGING THE HEADSET Before first time operation, place the headset securely in the base and allow the unit to charge undisturbed for 12 full hours. When fully charged, the headset indicator light will turn bright green. A full charge will provide 6 hours of talk time before needing to be recharged. A red light simply indicates less than a full charge-and it is okay to use the headset unless you hear the low battery warning while you are using the headset (see below).
BASIC OPERATIONS See page 6 for location of button controls. Standby Mode The headset is automatically in standby mode when you remove it from the base; therefore, a single press of the multifunction button will activate the headset. After removing the headset from the base, a yellow flashing light on the headset indicates that Standby Mode is active (you may need to wait 5 seconds to see it). If the yellow light is not flashing, turn the headset on (instructions below). 1.
Answer A Call / End A Call Answer A Call Un-Mute The Microphone On The Headset To un-mute the microphone, press and hold down the Increase Volume button for 4 seconds. You will hear a beep and the microphone will un-mute. Before answering, make sure the headset is in Standby Mode (page 14). 1. If the headset is not on your head, put it on and position the microphone properly. Switch From Headset To Handset While On A Call 2.
PAIRING See page 6 for location of button controls. For your convenience, the BlueParrott B200 base and headset have been paired in advance at the factory. However, if you have since paired the headset or the base with an alternate Bluetooth product, you will need to pair the BlueParrott B200 base and headset together again.
VISUAL AND AUDIO INDICATORS EXPLAINED Headset Indicator Lights / While In Base: No lights Bright green light Red light Headset Indicator Lights / While Off Base: Yellow flashing Red light flashes every few seconds Red/yellow lights flash alternately, then stop Headset Audio Indicators: 3 beeps that descend in tone 3 beeps that ascend in tone 1 single beep 1 single beep that repeats every few seconds Double beep every 30 seconds Base Unit Indicator Lights: Yellow flashing Red/yellow lights flash alternately
USA FCC Part 15 FCC Notice to Users/Product Statements This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Users are not permitted to make changes or modify the device in any way.
VXI LIMITED WARRANTY 1. VXI warrants that your BlueParrott B200 system will be free from defects in material and workmanship for two years from the date of purchase. If, during the first two years from the date of purchase, your BlueParrott B200 system fails to work due to a defect in material or workmanship, VXI will repair or replace the product, at its election, free of charge. Without proof of purchase, the warranty period begins on the date of manufacture. 2.
A brand of VXI Corporation One Front Street.