Data Sheet

ManualsBrandsWÜRTH ELEKTRONIK ManualsCase AccessoriesSpacer Brass 746

Dimensions: [mm]

5,0

0,57,0

sectional drawing A-A

0,5

3,0

Scale - 4:1

Recommended Land Pattern: [mm]

suggested

solder pad

non plated

2,95

2,45

0,25

Scale - 8:1

Stencil Suggestion:

0,45 2,75

2,25

Scale - 7:1

Properties Value Unit

Material Brass

Surface Tin

Solder Cream Thickness 120 µm

Tightening Torque 0.4 Nm

Operating Temperature -55 °C up to +150 °C

Properties:

Properties Test conditions Value Unit Tol.

Rated Current @ 20 °C I

50 A max.

Electrical Properties:

Packaging Tape and Reel

Packaging Unit (Qty.) Qty. 1600

Packaging Properties:

Würth Elektronik eiSos GmbH & Co. KG

EMC & Inductive Solutions

Max-Eyth-Str. 1

74638 Waldenburg

Germany

Tel. +49 (0) 79 42 945 - 0

www.we-online.com

eiSos@we-online.com

CREATED CHECKED GENERAL TOLERANCE PROJECTION

METHOD

DaSc JuSa DIN ISO 2768-1m

DESCRIPTION

REDCUBE SMD right angled

without Pins WP-SMRA

ORDER CODE

7466303R

REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

001.003 Valid 2017-11-22 eiCan 1/5

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH

& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety

must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.

Summary of content (5 pages)

PAGE 1
Dimensions: [mm] Recommended Land Pattern: [mm] suggested solder pad Properties: Properties non plated Value Unit Material Brass Surface Tin Solder Cream Thickness 120 µm Tightening Torque 0.4 Nm Operating Temperature -55 °C up to +150 °C Electrical Properties: 2,45 5,0 sectional drawing A-A A 2,95 M 3 3,0 5,0 0,5 0,25 Properties Test conditions Rated Current @ 20 °C IR Value Unit Tol. 50 A max.
PAGE 2
Packaging Specification - Tape and Reel: [mm] P0 K0 A D0 T E1 P2 W3 A C D1 A P1 T1 T2 A0 Feeding direction End NO COMPONENT min. 160mm N B D W B0 E2 F W1 close to center Start COMPONENTS W2 Carriertape Cover Tape NO COMPONENT min. 100mm COVER TAPE min. 400mm tolerance Tape width Packaging is reffered to the international standard IEC 60286-3:2013 tolerance size 7466303R A0 B0 W ±0,1 ±0,1 +0,3/ -0,1 5.3 7.3 16,00 T T1 T2 K0 P0 P1 P2 D0 +0,05 max. max.
PAGE 3
Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max TC –5°C Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) Ts min 60 - 120 seconds 3 °C/ second max.
PAGE 4
Cautions and Warnings: The following conditions apply to all goods within the product series of WP-SMRA of Würth Elektronik eiSos GmbH & Co. KG: General: All recommendations according to the general technical specifications of the data-sheet have to be complied with. The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer.
PAGE 5
Important Notes 6. Product Life Cycle The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG: Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance.