Data Sheet

ManualsBrandsWürth Elektronik ManualsCapacitorsWürth Elektronik WCAP-PHGP Aluminum Polymer Capacitors Electrolytic capacitor 7343 100 µF 6.3 V 1 pc(s)

Dimensions: [mm]

1,3 ±0,3

2,4 ±0,1

1,3 ±0,3

1,9 ±0,1

7,3 ±0,2

4,3 ±0,2

Scale - 5:1

Recommended Land Pattern: [mm]

4,0 2,4

2,8

8,8

Scale - 5:1

Schematic:

Properties Test conditions Value Unit Tol.

Capacitance C 0.5 V/ 120 Hz/ +20 °C 100 µF ±20%

Rated Voltage U

6.3 V (DC) max.

Surge Voltage U

1000 cycles @ 20 °C 7.8 V (DC) max.

Leakage Current I

Leak

2 min./ +20 °C 63 µA max.

Dissipation Factor DF 0.5 V/ 120 Hz/ +20 °C 6 % max.

Ripple Current I

RIPPLE

100 kHz @ 45 °C 5100 mA max.

ESR R

ESR

100 kHz @ 20°C 15 mΩ max.

Electrical Properties:

Aluminum Polymer Capacitors

Storage Conditions

(in original packaging)

5 °C - 30 °C; 10 % up to 70 % RH

Operating Temperature -55 up to +105 °C

Endurance 2000 h

Moisture Sensitivity Level (MSL) 3

Test conditions of Electrical Properties: +20 °C, 35 % RH if not specified differently

FIT according to separate documentation

Surge Voltage: Charging time 30s, discharging time 330s for a cycle

Component conform to REACh and RoHS requirements and standards

General Information:

Würth Elektronik eiSos GmbH & Co. KG

EMC & Inductive Solutions

Max-Eyth-Str. 1

74638 Waldenburg

Germany

Tel. +49 (0) 79 42 945 - 0

www.we-online.com

eiSos@we-online.com

CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE PROJECTION

METHOD

PSL 001.000 2018-11-13 DIN ISO 2768-1m

DESCRIPTION TECHNICAL REFERENCE

WCAP-PHGP Aluminum Polymer

Capacitors

PSE2917101M6R3DHCT1HT19

ORDER CODE

875015119003

SIZE/TYPE BUSINESS UNIT STATUS PAGE

7.3 x 4.3 x 1.9 eiCap Valid 1/8

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH

& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety

must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.

Summary of content (8 pages)

PAGE 1
Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: - Test conditions Capacitance C Rated Voltage UR Surge Voltage 2,8 + 2,4 ±0,1 Properties 1,3 ±0,3 1,3 ±0,3 1,9 ±0,1 4,0 US 0.5 V/ 120 Hz/ +20 °C Value Unit Tol. 100 µF ±20% 6.3 V (DC) max. 1000 cycles @ 20 °C 7.8 V (DC) max. Leakage Current ILeak 2 min./ +20 °C 63 µA max. Dissipation Factor DF 0.5 V/ 120 Hz/ +20 °C 6 % max. 5100 mA max. 15 mΩ max.
PAGE 2
Product Marking: 1st Line left WE Marking 1st Line right Capacitance Value 100 µF (Coding 100 ) 2nd Line left Lot Number 2nd Line right Rated Voltage: 6.3 V (DC) (Coding j ) Multiplier for Ripple Current vs. Frequency Frequency Multiplier 10 kHz ≤ freq. < 20 kHz 0.6 20 kHz ≤ freq. < 50 kHz 0.7 50 kHz ≤ freq. < 100 kHz 0.8 100 kHz ≤ freq. < 200 kHz 1.0 200 kHz ≤ freq. < 500 kHz 0.8 500 kHz ≤ freq. < 1 MHz 0.7 1 MHz ≤ freq. < 10 MHz 0.4 Multiplier for Ripple Current vs.
PAGE 3
Packaging Specification - Tape and Reel: [mm] P0 P2 T A D F W C E2 B0 W1 close to center B E1 D0 Top Cover Tape D1 A N A W3 K0 P1 W2 T1 A0 T2 End Start Feeding direction Carrier Tape detail B B Cover Tape Cover Tape Chip Cavity Sprocket Hole No Component min.160mm Components Embossment No Component min.100mm Cover Tape min. 400mm packaging is refered to the international standard IEC 60286-2 Tape Type 2a A0 (mm) typ. 4,50 B0 (mm) typ.
PAGE 4
Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max Ts min Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) 60 - 120 seconds 3 °C/ second max.
PAGE 5
Cautions and Warnings: The following conditions apply to all goods within the product series of Aluminium Polymer SMT H-Chip Capactiors of Würth Elektronik eiSos GmbH & Co. KG: General: • Do not expose the capacitor to environments with hazardous gas, ozone, ultraviolet rays or any kind of radiation. Avoid any contact of the capacitor with direct sunshine, saltwater, spray of water or types of oil during storage.
PAGE 6
Soldering: Adhesives and coating materials: • The solder profile must comply with the Würth Elektronik technical soldering specification. All other profiles will void the warranty. • All other soldering methods are at the customer’s own risk. • Strong forces which may affect the coplanarity of the component’s electrical connection with the PCB (i.e. pins), can damage the part, resulting in void of the warranty.
PAGE 7
Additional requirements for aluminum polymer capacitors: Circuits and designs where the usage of Stack Type Aluminum Polymer Capacitors is prohibited are: • High-impedance circuits • Coupling circuits • Time constant circuits Due to thermal stress, the leakage of aluminum polymer capacitor can vary within the above stated applications.
PAGE 8
Important Notes 6. Product Life Cycle The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG: Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance.