Installation Guide

ManualsBrandsWAC Lighting ManualsLandscape Lighting2" Wide LED Slim Inground Light with Clear Glass - 12 Volt

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2016 1

waclighting.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

SAFETY INSTRUCTION

IMPORTANT: NEVER attempt any work without shutting o the electricity.

• Read all instructions before installing.

• System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

• Place the wall switch in the “OFF” position.

• Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the

space that you are working on.

CAUTION:

All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out

or broken. Failure to follow this instruction could invalidate the ETL/cETL listing of this xture.

AVERTISSEMENT

IMPORTANT : COUPEZ L’ÉLECTRICITÉ AVANT TOUTE MANIPULATION.

• Lisez toutes les instructions avant d’installer.

• Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.

• Placez l’interrupteur mural en position d’arrêt (« OFF »).

• Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).

MISE EN GARDE

Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les

utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/cETL du luminaire.

THIS INSTRUCTIONS APPLY TO THE MODELS BELOW:

Fixture Accessory (included in box)

Outdoor Rated Wire Nut

Model: 9020-WNT-BK

Qty: 2pcs

2011

2012

2021/2031

2022

2051

2052

1011 1021 1051

2041 2061

INSTALLATION INSTRUCTION

Mini In-Ground

1011/ 1021/ 1051/ 2011/ 2012 / 2021/ 2022

2031/ 2041 / 2051 / 2052 / 2061

*Note: Transformer is required to power the xture. (sold separately)

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTION Mini In-Ground 1011/ 1021/ 1051/ 2011/ 2012 / 2021/ 2022 2031/ 2041 / 2051 / 2052 / 2061 SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. • Place the wall switch in the “OFF” position. • Go to the main fuse box, or circuit breaker.
PAGE 2
INSTALLATION INSTRUCTION Mini In-Ground 1011/ 1021/ 1051/ 2011/ 2012 / 2021/ 2022 2031/ 2041 / 2051 / 2052 / 2061 SOFTSCAPE INSTALLATION *Note: Transformer is required to power the fixture. (sold separately) 1. Turn the main power off. 2. Dig a hole at the point of application. Make sure the hole measures roughly ØA* in diameter and 4 inches in depth. (Fig.1) 3. Place a layer of pea gravel at the base of the hole to help with drainage. 4.
PAGE 3
INSTALLATION INSTRUCTION Mini In-Ground 1011/ 1021/ 1051/ 2011/ 2012 / 2021/ 2022 2031/ 2041 / 2051 / 2052 / 2061 OUTDOOR WALL INSTALLATION *Note: Transformer is required to power the fixture. (sold separately) UL listed for outdoor use only 1. Turn the main power off. 2. Attach the spring clip using the provided clip screws. 3. Cut a hole at the installation location. (Fig.3) 4.
PAGE 4
INSTALLATION INSTRUCTION Mini In-Ground 1011/ 1021/ 1051/ 2011/ 2012 / 2021/ 2022 2031/ 2041 / 2051 / 2052 / 2061 CONCRETE POUR INSTALLATION *Note: Transformer is required to power the fixture. (sold separately) For model # 1011/1021/1051: D* = Ø1.32 in. Fig.5 Schedule 80 PVC Pipe (Not Provided) 1. Turn the main power off. 2. Install wiring and conduit (use ½” NPT) at desired position, plug all un-used holes. Refer to applicable wiring diagram. (Fig.5) 3.