Installation Sheet

ManualsBrandsWAC Lighting ManualsAll WAC LightingWAC Lighting Tube Single Light 6-5/16" Wide Integrated LED Outdoor Mini Pendant with 19° Beam Spread

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 1

waclighting.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Tube Architectural - Pendant

DS-PD05, DS-PD06, DS-PD08

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch “OFF” the circuit

breaker switch (es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

FIXTURE INSTALLATION

1. Carefully unpack xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

Refer to Fig.1

2. Determine desired height. Combine stems together and /or eld cut stems as necessary to achieve desired suspension height.

Note: additional stems (p/n DS-PDX24) can be combined for a maximum length of 96”. Refer to Fig. 2-4

Cast ball

5”

1/2”

Junction box

Canopy

Pendant stem

Pendant xture

Mounting plate

Canopy

24” stem (X2)

Screws

Fixture plate

Washer

Nut

Pendant xture

Feed wire

Feed wire clamp

Pendant stem Thread connector Metal cutting tool

Fig.1

Fig.3

Fig.2

Fig.4

96” max

Summary of content (3 pages)

PAGE 1
INSTALLATION INSTRUCTION Tube Architectural - Pendant DS-PD05, DS-PD06, DS-PD08 WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. - Go to the main fuse box, or circuit breaker.
PAGE 2
INSTALLATION INSTRUCTION Tube Architectural - Pendant DS-PD05, DS-PD06, DS-PD08 3. 4. 5. Align the top of the cast ball with the top of the cut pendant stem and temporarily lock it in place by tightening one of the screws into the side of the stem. Use the provided drill bit to drill a hole through the stem wall using the unthreaded hole. Loosen the screw. Rotate the cast ball 180° and retighten the screw. Drill another hole using the unthreaded hole on the other side of the stem wall. Loosen the screw.
PAGE 3
INSTALLATION INSTRUCTION Tube Architectural - Pendant DS-PD05, DS-PD06, DS-PD08 REFLECTOR REPLACEMENT 1. Remove panel assembly by loosening the fixture screw and gasket, remove three chips to change reflector. (Fig.10) 2. Replace your beam angle reflector on panel and fix the clips. (Fig.11) Fig.10 Fig.11 Remove three clips Put on reflector and fix clips Replace different beam angle reflector LED REPLACEMENT 1. Loosen the fixture screw and gasket (Fig.12), remove the panel assembly (Fig.13). 2.