Specification Sheet
Fixture Type:
Catalog Number:
Project:
Location:
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY 22, 2018 3:37 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
LED DIMMER & DRIVER
All-in-One Wall Unit
PRODUCT DESCRIPTION
WAC Dimmer & Driver simplies LED array lighting systems by combining
an in-wall LED dimmer switch and power supply into a single integrated
unit. Mounts in a standard in-wall switch box, accepts 120V AC and
converts to low voltage DC. WAC Dimmer & Driver is compatible with most
solid color 24VDC tape lights and xtures.
FEATURES
• LED Driver & In-Wall Dimmer Switch in one unit, ts in a standard
recessed electrical box.
• 100% - 1% smooth dimming.
• No minimum load.
• Single Pole preset dimmer with on/o push switch.
• Adjustable voltage output dial to address voltage drop.
• Includes voltage barrier partition to install high and low voltage
circuit in same switch box.
• No derating required when ganging units.
• Power failure memory: If power is interrupted, WAC Dimmer + Driver
will return to setting prior to interruption.
• Three face plates included: Glossy Dark Brown, Glossy Light Almond,
and Glossy White (trim plates not included).
SPECIFICATIONS
INPUT
Input Voltage:
Input Current:
In-Rush Current:
Leakage Current:
Power Factor:
Total Harmonic
Distortion (THD):
Stand-by-power:
Eciency:
OUTPUT
Dimming:
Voltage
Adjustment Dial:
Startup Time:
Standards:
120VAC (108 ~ 132VAC), 50/60Hz (47 ~ 63Hz)
<1.0A @ 120VAC max load
Meets NEMA-410 requirement at any nominal input full sine
wave voltage and maximum load at 25°C
<500μA @ 120VAC
>0.9 @ 120VAC 60Hz max load
≤20% @ 120VAC 60Hz max load. Tested to comply in
accordance with IEC 61000-3-2.
≤0.5W
≥91% @ 120VAC max load
Output voltage is adjustable via sliding lever
Increases output +1V to compensate for voltage drop from
control to luminaire.
The main supply output voltages remain within the
regulation limit of +/- 3%
UL & cUL Listed for dry locations Low Voltage Lighting
System #E469769; FCC Approved; Complies with the limits
for a Class B digital device, pursuant to Part 15 of the FCC
Rules; RoHS Certied; CE Certied; Conforms to NEC Code
725.136 (See Mechanical Diagram): Class 1 and Class 2
circuit in same enclosure must be separated by a barrier
(partition) unless Class 2 circuit conductors are install in
accordance with 725.41 Class 1 Circuits.
Surge/Transient: Tested to meet transients dened in IEC
6100-4-4, level 3 & IEC 6100-4-5, level 3.
Protections: Short circuit, thermal runway, and over voltage.
Model Input Voltage Output Voltage Max Load Color
END24100120R 120VAC 24VDC 100W, 4.2A
Glossy Dark Brown
Glossy Light Almond
Glossy White
0.1 in.
(3mm)
3.82 in. (97mm)
3.3 in. (83mm)
2.6 in. (66mm)
1.3 in. (33mm)
2.1 in. (54mm)
1.8 in. (47mm)1.4 in. (35mm)
0.2 in.
(6mm)