User manual

Operating
temperature
Sealing
Material
Digital Inputs
Outputs
OUT 24V
Back-UP
Power Supply
TECHNICAL DATATECHNICAL DATA
Operating temperature 0-40°C, humidity
35..95uR%
IP65 (with gasket) on front panel,
IP20 box and terminal blocks
PC ABS UL94V0 self-extinguishing
3PNP/NPN configurable as analogue for
potentiometers.(max 28 Vdc in PNP mode)
2 relays 8A resistive charge
30mA(24Vac),40mA(24 Vdc),60mA (110...230Vac)
Rechargeable battery, approx. 60days autonomy
24...230Vac/Vdc +/-15% 50/60Hz / 2W
.
INTRODUCTION
Thanks for choosing a Wachendorff device.
The timer TI484801 can be set in 5 different modes; Timer-ON, Timer-
OFF, Pause-Work, Oscillator, PWM (time-proportioned output), all
options with independent settings of ON-OFF time.
3 universal digital inputs are availables (NPN/PNP/Potential free
contact) for external commands like Start, Stop and Reset; one input is
also analogue in order to allow the modification of working times by an
external potentiometer.
5 different time bases (hundredths, tenths, seconds, minutes, hours).
Counting can be incremental or decremental.
MEMORY CARD (optional)MEMORY CARD (optional)
Parameters and setpoint values can be copied from one device to another using
the Memory card
There are two methods:
insert the memory card .
On activation display 1 shows and display 2 shows
The device loads the new data and starts again
The memory card is equipped with an internal battery with a life of about 1000 uses.
Insert the memory card and press the programming button.
When writing the parameters, the LED turns red and on completing the procedure
it changes to green. It is possible to repeat the procedure.
To the memory card values, follow the procedure described in the first
method, setting display 2 to so as not to load the parameters on controller.
Enter configuration and .
Exit configuration. Changes are saved automatically.
This procedure restores the factory settings of the instrument.
With the device connected to the power supply
when the controller is off
With the controller disconnected from the power supply:
change at least one parameter
update
LOADING DEFAULT VALUES
.
(Only if the values stored on Mmeory Card are correct).
By pressing the key display 2 shows
Confirm using the key .
.
Attention: Pls. perform an update of the memory card first.
>
>
UPDATING MEMORY CARD.
LIST OF PARAMETERSLIST OF PARAMETERS
Potentiometer:
1-
2-
3-
4-
To modify Set1 or Set2 by external potentiometer follow the steps below:
use potentiometers 0 to 5/10kohm
connect cursor to pin I3; a wrong connection may damage the potentiometer and
lead to lock of the device.
accuracy on input is max 1000 points, therefore set the parameters "Upper limit"
and "Lower limit" with a max difference of 1000 units.
(Ex.: LoS1 to 50,0 and uPS1 to 150,0 to modify time value related to Set1 between
50 and 150 seconds with steps of one tenth). Greater differences would make
unstable the less significant digit.
To calibrate the scale of potentiometer enter the configuration mode and select:
Hin.3 as Pot
Fin.3 as Set1 or Set2
P.tAr as Enable
Exit configuration mode and place potentiometer at minimum level and press key,
then place potentiometer at max level and press premere key: the device
automatically exit the calibration procedure.
N.B.:Aswitch-off of the device would interrupt the calibration.
P-01 Timer Function
FUNCTION CONFIGURATION
P-02 Power-off Memory
Disable
Only Timer
Timer / State
BACKUP MEMORY CONFIGURATION
P-03 Hardware Input 1
INPUT CONFIGURATION
Timer functions
Activates output at count end
Deactivates output at count end
T1 and T2 start in sequency
Percentage output activation on fixed time base
T1 and T2 start in sequency repeatedly
Power-off memory
Disabled
Only timer value in memory
Timer value and START/STOP status in memory
NPN
PNP
TTL
NPN
PNP
TTL
P-04 Hardware Input 2
Input 1 configuration
NPN
PNP
TTL
NPN
PNP
TTL
Input 2 configuration
Default
Default
Default
Default
PRESS
Visualizes SETPOINT 1 / 2
DISPLAY
or
Modifies selecter SET
1
2
SETPOINT MODIFICATIONSETPOINT MODIFICATION
PRESS
On display 1 appears
with 1st digit blinking, while
display 2 shows
DISPLAY DO
or
Modify blinking digit and
pass to the next one pressing
Enter Password
to confirm
Display shows first parameter of
configuration table
1
2
3
Scroll parameters
4
or
Increase or decrease visualized value
pressing and an arrow key
Enter the new data
that will be
saved when releasing keys
5
+ or
End configuration, controller exits
from configuration
6
CONFIGURATION PARAMETER MODIFICATIONCONFIGURATION PARAMETER MODIFICATION
SET for
3 seconds
+
PRESS
On display 1 appears
with 1st digit blinking, while
display 2 shows
DISPLAY DO
or
Modify blinking digit and
pass to the next one pressing
Enter Password
to confirm
Device loads
default values
Switch the device off
and restart it
1
2
3
LOADING DEFAULT VALUESLOADING DEFAULT VALUES
SET for
3 seconds
SETPOINT CONFIGURATION
OUTPUT CONFIGURATION
DISPLAY CONFIGURATION
P-05 Hardware Input 3
P-06 Active State Input 1
P-07 Active State Input 2
P-08 Active State Input 3
PNP
TTL
Potent.
High Level
Low Level
Rising edge
High Level
Low Level
Rising edge
High Level
Low Level
Rising edge
Input 3 configuration
Input 1 activation
Input 2 activation
Input 3 activation
PNP
TTL
Potentiometer
High level
Low level
Transitory in rising
High level
Low level
Transitory in rising
High level
Low level
Transitory in rising
P-09 Function Input 1
P-12 Function Key UP
P-10 Function Input 2
P-11 Function Input 3
P-16 Format Set 1
P-18 Display Set 1
P-17 Format Set 2
P-19 Display Set 2
P-13 Output Q1 Setup
P-14 Output Q2 Setup
P-15 Type of Timer
Disable
Start / Stop
Start / Stop-Reset
Reset-Start / Stop
Reset / Start / Stop
Second.Cent
Second.Decimal
Second
Minute.Second
Hour.Minute
Hour
Disable
Start / Stop
Start / Stop-Reset
Reset-Start / Stop
Reset / Start / Stop
Reset
Wait
Hold
Disable
Out Timer 1 n.o.
Out Timer 1 n.c.
Out Timer 2 n.o.
Out Timer 2 n.c.
Start
Stop
Disable
Out Timer 1 n.o.
Out Timer 1 n.c.
Out Timer 2 n.o.
Out Timer 2 n.c.
Start
Stop
Incremental
Decremental
Disable
Visualized
Modifiable
Disable
Visualized
Modifiable
Disable
Enable
P-24 Potent. tarature
P-20 Lower limit Set 1
P-21 Upper limit Set 1
P-22 Lower limit Set 2
P-23 Upper limit Set 2
Disable
Reset
Disable
Wait
Hold
Potent. To SET1
Potent. To SET2
Input 1 function
Function of
Input 2 function
Input 3 function
Count format
Set 1 visualization
Count format
Set 2 visualization
Output Q1 selection
Output Q2 selection
Count mode
Disabled
Start / Stop
Start / Stop-Reset
Reset-Start / Stop
Reset / Start / Stop
Seconds, Cents
Seconds, Tenths
Seconds
Minutes, Seconds
Hour, Minutes
Hour
Disabled
locks display but count continuels
Start / Stop
Start / Stop-Reset
Reset-Start / Stop
Reset / Start / Stop
Reset
Wait (count lock)
Hold ( )
Disabled
Timer output 1 n.c.
Timer output 2 n.o.
Timer output 2 n.c.
Timer output 1 n.o.
Start
Stop
Disabled
Timer output 1 n.o.
Timer output 1 n.c.
Timer output 2 n.o.
Timer output 2 n.c.
Start
Stop
Incremental
Decremental
Disabled
Visualized
Visualized and modifiable
Disabled
Visualized
Visualized and modifiable
Disabled
Enabled
Potentiometer calibration procedure
Set 1 lower limit
Set 1 upper limit
Set 2 lower limit
Set 2 upper limit
Reset
Disabled
Modify SET1 by potentiometer
Disabled
Wait (count lock)
Hold (locks display but count continues)
Modify SET2 by potentiometer
Default
Default
Default
Default
Default
Default
Default
Default
Default
Default
Default
Default
Default
Default
0.0
0.0
99.9
99.9
Default
SIZE AND INSTALLATIONSIZE AND INSTALLATION
Timer On
Timer Off
Pause/Work
Oscillator
PWM
NPN PNP
POTENTIOMETER 0 to 5/10 Kohm
Accuracy 1.000 points
PNP
NPN
WIRING DIAGRAMWIRING DIAGRAM
-
+
OUTPUT
5
4
3
2
1
I3
10
9
8
7
6
SUPPLY
24...230V
AC/DC
8A 230V
Resistiv
1/2HP
CAUTION
Risk of Electric Shock
Disconnect power
supply before
servicing
I2
I1
OUT 24V
Q2
8A 230V
Resistiv
1/2HP
Q1
Proximity
Sensor PNP
3 wires
Proximity
Sensor PNP
2 wires
I1
I2
I3
I1
I2
I3
5
4
3
2
1
I3
10
9
8
7
6
SUPPLY
24...230V
AC/DC
8A 230V
Resistiv
1/2HP
CAUTION
Risk of Electric Shock
Disconnect power
supply before
servicing
I2
I1
OUT 24V
Q2
8A 230V
Resistiv
1/2HP
Q1
5
4
3
2
1
I3
10
9
8
7
6
SUPPLY
24...230V
AC/DC
8A 230V
Resistiv
1/2HP
CAUTION
Risk of Electric Shock
Disconnect power
supply before
servicing
I2
I1
OUT 24V
Q2
8A 230V
Resistiv
1/2HP
Q1
5
4
3
2
1
I3
10
9
8
7
6
SUPPLY
24...230V
AC/DC
8A 230V
Resistiv
1/2HP
CAUTION
Risk of Electric Shock
Disconnect power
supply before
servicing
I2
I1
OUT 24V
Q2
8A 230V
Resistiv
1/2HP
Q1
Report the activation of Q1
MEANING
Report the activation of Q2
LED
Report serial transmission by the TI484801
A3
MAN TUN REM
C1C 1
C2C 2
A1
A2
A3
MAN TUN REM
C1C 1
C2C 2
A1
A2
A3
MAN TUN REM
C1C 1
C2C 2
A1
A2
Read carefully the safety guidelines and programming instructions
contained in this manual before using/connecting the device.
Disconnect power supply before proceeding to hardware settings or
electrical wirings.
Only qualified personnel should be allowed to use the device and/or
service it and in accordance to technical data and environmental
conditions listed in this manual.
Do not dispose electric tools together with household waste materials in
observance of European Directive 2002/96/CE
48 mm
48 mm
Front panel
cut out
46x46mm
2to mm
suggested thickness
6
106 mm10
A3
MAN TUN REM
C1C 1
C2C 2
A1
A2
16
Memory Card
Insertion of
memory card (optional)
1
5
2
3
4
5
4
3
2
1
I3
10
9
8
7
6
Versorg.
24...230V
AC/DC
8A 230V
Resistiv
1/2HP
ACHTUNG
Gefahr eines elektr.
Schlags. Schalten Sie
die Versorgung vor
dem
Service ab.
I2
I1
OUT
2
4V
50mA
Q2
8A 230V
Resistiv
1/2HP
Q1
MEMORY C.241MEMORY C.241
CN1
1 6
MANUAL
TIMER TI484801
MANUAL
TIMER
TI484801
Wachendorff Prozesstechnik GmbH & Co. KG
www.wp-direkt.de
e-mail: [e-mail]
Version 2.0