User manual

Timer On
Stop/Reset
Start/Stop/Reset
Reset
Wait/Hold/Set1-2
Timer Off
Start/Stop/Reset
Reset
Wait/Hold/Set1-2
Start/Stop/Reset/Wait/Hold
Oscillator
Start/Stop/Reset
Reset
Wait/Hold/Set1-2
Start/Stop/Reset/Wait/Hold
PWM
Start/Stop/Reset
Reset
Wait/Hold/Set1-2
Start/Stop/Reset/Wait/Hold
Pause / Work
Start/Stop/Reset
Reset
Wait/Hold/Set1-2
Start/Stop/Reset/Wait/Hold
TI484801 “TIMER”
P-01
Timer
Function
Timer On (Nota 1)
Timer Off (Nota 1)
Pause/Work (Nota 1)
Oscillator
PWM
FUNCTION CONFIGURATION
P-02
Power-off
Memory
Disable
Only Timer
Timer / State
POWER-ON
RESET
BACKUP MEMORY CONFIGURATION
Timer value
Out Timer 1
Out Timer 2
Start/Stop/Reset/Wait/Hold
Set1
Set2
Stop/Reset
Set1
Set2
Stop/Reset
Set1
Set2
Stop/Reset
Set1
Set2
Stop/Reset
Set1
Set2
P-06
Active State
Input 1
High Level
Low Level
Rising edge
Disable
Start / Stop (Nota 2)
Start / Stop-Reset
Reset-Start / Stop
Reset / Start / Stop
(Note 3)
(Note 4)
(Note 5)
P-09
Function
Input 1
I1
P-03
Hardware
Input 1
NPN
PNP
TTL
Disable
Start / Stop (Nota 2)
Start / Stop-Reset (Note 3)
Reset-Start / Stop (Note 4)
Reset / Start / Stop
Reset
Wait
Hold
P-12
Function
Key UP
Key UP
P-07
Active State
Input 2
High Level
Low Level
Rising edge
I2
P-04
Hardware
Input 2
NPN
PNP
TTL
Disable
Reset
P-10
Function
Input 2
P-08
Active State
Input 3
High Level
Low Level
Rising edge
I3
P-05
Hardware
Input 3
PNP
TTL
Potent.
Disable
Wait
Hold
Potent. To SET1
Potent. To SET2
P-11
Function
Input 3
P-24
Potentiometer
calibration
Disable
Enable
INPUT CONFIGURATION
Second.Cent
Second.Decimal
Second
Minute.Second
Hour.Minute
Hour
P-16
Format
Set 1
Disable
Visualized
Modifiable
P-18
Display
Set 1
P-20
Lower limit
Set 1
P-21
Upper limit
Set 1
Disable
Visualized
Modifiable
Second.Cent
Second.Decimal
Second
Minute.Second
Hour.Minute
Hour
P-17
Format
Set 2
P-19
Display
Set 2
P-22
Lower limit
Set 2
P-23
Upper limit
Set 2
SETPOINT CONFIGURATION
Timer value
Out Timer 1
Out Timer 2
Timer value
Out Timer 1
Out Timer 2
Timer value
Out Timer 1
Out Timer 2
Timer value
Out Timer 1
Out Timer 2
Q2
Q1
P-13
Output Q1
Setup
Disable
Out Timer 1 n.o.
Out Timer 1 n.c.
Out Timer 2 n.o.
Out Timer 2 n.c.
Start
Stop
P-14
Output Q2
Setup
Disable
Out Timer 1 n.o.
Out Timer 1 n.c.
Out Timer 2 n.o.
Out Timer 2 n.c.
Start
Stop
OUTPUT CONFIGURATION
DISPLAY CONFIGURATION
P-15
Type
of Timer
Incremental
Decremental
1
2
3
Set
SET1
Time
1
0
Out Timer 1
Start
Stop
Reset
TIMER 1TIMER 1
1
0
1
0
1
0
Set
SET1
Time
1
0
Out Timer 1
Start
Stop
Reset
TIMER 1TIMER 1
1
0
1
0
1
0
Set
SET1
Time
1
0
Out Timer 1
Out Timer 2
Start
Stop
TIMER 1TIMER 1
1
0
1
0
1
0
SET2
TIMER 2TIMER 2
Set
SET1
Time
1
0
Out Timer 1
Out Timer 2
Start
Stop
TIMER 1TIMER 1
1
0
1
0
1
0
SET2
TIMER 2TIMER 2
Set
SET2 (Period)SET2 (Period)
Time
1
0
Out Timer 1
Out Timer 2
Start
Stop
TIMER 1
TIMER 1
1
0
1
0
1
0
SET1(% duty-Cycle)SET1(% duty-Cycle)
In PWM mode, the only option available on
parameters 16 and 17 for format of
SET1 and SET2 is (seconds).
Low and upper limits for SET1 (related to
percentage of work or Duty Cycle) are allowed in
the range 0 ... 100 (%).
Note 1: In this timer functioning, if
Note 2: This function not reset timer value, and so it requires an input for the reset.
P-06 Active State Input 1 = Rising Edge or P-09 Function Input 1 = Disable,
at count end (reaching setpoint), timer will switch automatically to STOP.
Nota 3: This function reset timer at STOP.
Note 4: This function reset timer at START.
Note 5: This function è attiva solo se P-06 Active State Input 1 = Rising Edge
ERROR WRITING EEPROM Memory (Note 1)
TABLE of ERROR MESSAGESTABLE of ERROR MESSAGES
Note 1:
Switch the device off and restart it; if error is still notified, contact
technical service
Note 2:
Discharged battery: keep the device connected to power supply in
order to recharge the battery.
ERROR READING EEPROM Memory (Note 1)
Incorrect parameters (Note 1)
Incorrect calibration data (Note 1)
Incorrect status data (Note 1)
Incorrect BACKUP registers (Note 2)
LOGIC
LEVEL
H
L
NPN
INPUT
< 4,7 v
> 5,7 v
PNP
INPUT
>5,7 v (I1, I2)
>12,4 v (I3)
< 4,7 v (I1, I2)
< 10,2 v (I3)
INPUT
TYPE
TTL
INPUT
>2,5 v
< 2,0 v