Operator’s Manual Vibroplate VP 1340 VP1340W VP 1340W-L VP 1340W-LL VP 1340W-LF VP1550 VP1550W 5000190492 5 0 0 0 1 12 9 0 0811 4 9 2
Copyright notice © Copyright 2011 by Wacker Neuson Corporation. All rights, including copying and distribution rights, are reserved. This publication may be photocopied by the original purchaser of the machine. Any other type of reproduction is prohibited without express written permission from Wacker Neuson Corporation. Any type of reproduction or distribution not authorized by Wacker Neuson Corporation represents an infringement of valid copyrights. Violators will be prosecuted.
VP 1340/VP 1550 Table of Contents Foreword 3 1. Emission System Control Information 4 2. Safety Information 9 3. 4. 2.1 Laws Pertaining to Spark Arresters ...................................................... 9 2.2 Operating Safety ................................................................................ 10 2.3 Operator Safety while using Internal Combustion Engines ................ 11 2.4 Service Safety .............................................................................
Table of Contents 5. VP 1340/VP 1550 Maintenance 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 24 Maintaining the Emission Control System............................................24 Periodic Maintenance Schedule ..........................................................24 Spark Plug ...........................................................................................26 Air Cleaner ..........................................................................................
WARNING CALIFORNIA Proposition 65 Warning: Engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Foreword This manual provides information and procedures to safely operate and maintain this Wacker Neuson model. For your own safety and protection from injury, carefully read, understand and observe the safety instructions described in this manual.
Emission Control Systems Information and Warranty 1 Emission Control Systems Information and Warranty The Emission Control Warranty and associated information is valid only for the U.S.A., its territories, and Canada. 1.1 Emission Control System Background Information Introduction Wacker Neuson spark-ignited engines/equipment must conform with applicable Environmental Protection Agency (EPA) and the State of California emissions regulations.
Emission Control Systems Information and Warranty Tampering and Altering Tampering with or altering the emission control system may increase emissions beyond the legal limit. If evidence of tampering is found, Wacker Neuson may deny a warranty claim. Among those acts that constitute tampering are: Removing or altering of any part of the air intake, fuel, or exhaust systems. Altering or defeating the speed-adjusting mechanism causing the engine to operate outside its design parameters. 1.
Emission Control Systems Information and Warranty applicable EPA regulations. All defective parts replaced under this warranty become property of Wacker Neuson.
Emission Control Systems Information and Warranty What is not covered Failures other than those resulting from defects in material or workmanship. Any systems or parts which are affected or damaged by owner abuse, tampering, neglect, improper maintenance, misuse, improper fueling, improper storage, accident and/or collision; the incorporation of, or any use of, add-on or modified parts, or unsuitable attachments, or the alteration of any part.
Emission Control Systems Information and Warranty For owners located more than 100 miles from an authorized dealer/service center (excluding the states with high-altitude areas as identified in 40 CFR Part 1068, Appendix III), Wacker Neuson will pay for pre-approved shipping costs to and from an authorized Wacker Neuson dealer/service center.
VP 1340/VP 1550 2. Safety Information Safety Information This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE signal words which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Safety Information 2.2 VP 1340/VP 1550 Operating Safety WARNING Familiarity and proper training are required for the safe operation of the machine. Machines operated improperly or by untrained personnel can be hazardous. Read the operating instructions contained in this manual and the engine manual, and familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive instruction from someone familiar with the machine before being allowed to operate it. 2.2.
VP 1340/VP 1550 2.3 Safety Information Operator Safety while using Internal Combustion Engines WARNING Internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. Failure to follow the warnings and safety standards could result in severe injury or death. 2.3.
Safety Information 2.4 VP 1340/VP 1550 Service Safety A poorly maintained machine can become a safety hazard! In order for the machine to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. WARNING 2.4.1 Do not attempt to clean or service the machine while it is running. Rotating parts can cause severe injury. 2.4.2 Do not crank a flooded engine with the spark plug removed on gasoline-powered engines.
VP 1340/VP 1550 2.5 Safety Information Label Locations wpmgr005950 wpm_si000317gb.
Safety Information 2.6 VP 1340/VP 1550 Warning and Informational Labels Wacker Neuson machines use international pictorial labels where needed. These labels are described below. Label Meaning WARNING! Always wear hearing and eye protection when operating this machine. WARNING! Hot surface! Guaranteed sound power level in dB(A). WARNING! Hand injury if caught in moving belt. Always replace beltguard. CAUTION! Read and understand the supplied Operator’s Manual before operating this machine.
VP 1340/VP 1550 Label Safety Information Meaning Throttle control lever: Turtle = Idle or Slow Rabbit = Full or Fast DANGER! Engines emit carbon monoxide; operate only in well-ventilated area. Read the Operator’s Manual. No sparks, flames, or burning objects near the machine. Shut off the engine before refueling. Label-machine model Company logo Company label A nameplate listing the model number, item number, revision number, and serial number is attached to each unit.
Safety Information Label VP 1340/VP 1550 Meaning This machine may be covered by one or more patents. wpm_si000317gb.
VP 1340/VP 1550 3. Technical Data Technical Data 3.1 Engine Data Engine Power Rating Net power rating per SAE J1349. Actual power output may vary due to conditions of specific use. VP 1340, VP 1340 W 0008705, 0008706 VP 1550, VP 1550 W 0008707, 0008708 VP 1550 W 0630013 VP 1340 W-L 0630001 VP 1340 W-LL 0630002 VP 1340 W-LF 0630003 Engine Engine Make Wacker Engine Model WM170 Max. rated power @ rated speed kW (Hp) 4.2 (5.
Technical Data 3.2 VP 1340/VP 1550 Machine Data VP 1340, VP 1340 W 0008705, 0008706 VP 1340W - L 0630001 VP 1340W - LL 0630002 VP 1340W - LF 0630003 VP 1550, VP 1550 W 0008707, 0008708 VP 1550 W 0630013 Plate Weight kg (lbs.) Water Tank Capacity l (qts.) Exciter Speed rpm Exciter Lubrication ml (oz.) 3.3 VP 1340: 74 (163) VP 1340W: 76 (168) VP 1340W-L: 76 (168) VP 1340W-LL: 76 (168) VP 1340W-LF: 76 (168) VP 1550: 83 (184) VP 1550W: 86 (190) 3.8 (4.0) 7.6 (8.
VP 1340/VP 1550 3.4 Technical Data Dimensions mm (in.) 911 (36) 588 (23) VP1340 = 400 (16) VP1550 = 500 (20) wpm_td000326gb.
Operation 4. VP 1340/VP 1550 Operation 4.1 Recommended Fuel The engine requires regular grade unleaded gasoline. Use only fresh, clean gasoline. Gasoline containing water or dirt will damage fuel system. Consult engine owner’s manual for complete fuel specifications. Use of oxygenated fuels Some conventional gasolines are blended with alcohol. These gasolines are collectively referred to as oxygenated fuels.
VP 1340/VP 1550 4.3 Operation Before Starting 4.3.1 Read and understand the safety and operating instructions at the beginning of this manual. 4.3.2 Check: wpm_tx001111gb.
Operation 4.4 VP 1340/VP 1550 To Start See Graphic: wc_gr000655 4.4.1 Open fuel valve by moving lever down (a1). Note: If engine is cold, move choke lever to close position (d2). If engine is hot, set choke to open position (d1). 4.4.2 Turn engine switch to “ON” (b2). 4.4.3 Open throttle by moving it slightly to left (c2). 4.4.4 Pull starter rope (e). Note: If the oil level in the engine is low, the engine will not start. If this happens, add oil to engine. 4.4.5 Open choke as engine warms (d1).
VP 1340/VP 1550 4.6 Operation Operation Run the engine at full throttle and allow the plate to pull itself along at its normal speed. When operating on an incline it may be necessary to assist the plate by pushing it forward slightly. When operating downhill hold the plate back slightly, if it begins to pick up speed. Depending on the material being compacted, three or four passes are recommended to achieve the best compaction.
Maintenance 5. VP 1340/VP 1550 Maintenance 5.1 Maintaining the Emission Control System Normal maintenance, replacement or repair of emission control devices and systems may be performed by any repair establishment or individual; however, warranty repairs must be performed by a dealer/service center authorized by WACKER NEUSON.
VP 1340/VP 1550 Maintenance Machine Maintenance The chart below lists basic machine maintenance. Daily before starting Check external hardware. After first 20 hrs. Every 2 weeks or 50 hrs. Every month or 100 hrs. Every year or 300 hrs. Check and adjust drive belt. Inspect shockmounts for damage. Replace shockmounts as needed. Change exciter oil.
Maintenance 5.3 VP 1340/VP 1550 Spark Plug See Graphic: wc_gr000028 Clean or replace the spark plug as needed to ensure proper operation. Refer to your engine operator’s manual. The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Do not touch the muffler while it is hot. WARNING Note: Refer to section “Technical Data” for the recommended spark plug type and the electrode gap setting. 5.3.1 Remove the spark plug and inspect it. 5.3.
VP 1340/VP 1550 5.4 Maintenance Air Cleaner See Graphic: wc_gr000656 NEVER use gasoline or other types of low-flash point solvents for cleaning the air cleaner. A fire or explosion could result. WARNING NOTICE: NEVER run the engine without the air cleaner. Severe engine damage will occur. The engine is equipped with a dual-element air cleaner. Under normal operating conditions, the elements should be cleaned once every week. Under severe, dry and dusty conditions, the elements should be maintained daily.
Maintenance 5.5 VP 1340/VP 1550 Engine Oil See Graphic: wc_gr000087 5.5.1 Drain oil while engine is still warm. Note: In the interests of environmental protection, place a plastic sheet and a container under the machine to collect any liquid which drains off. Dispose of this liquid in accordance with environmental protection legislation. 5.5.2 Remove the oil drain plug (a). 5.5.3 Allow the oil to drain. 5.5.4 Install the drain plug. 5.5.
VP 1340/VP 1550 5.7 Maintenance Cleaning the Fuel Strainer 5.7.1 To remove water and dirt, close the fuel lever and remove the fuel strainer. 5.7.2 Inspect the fuel strainer (a) for water and dirt. 5.7.3 After removing any dirt and water, wash the fuel cup with a nonflammable solvent. 5.7.4 Reinstall securely to prevent leakage. wpm_tx001112gb.
Maintenance 5.8 VP 1340/VP 1550 Drive Belt See Graphic: wpmgr005993 On new machines or after installing a new belt, check the belt tension after first 20 hours of operation. Check and adjust the belt every 50 hours thereafter. To adjust the belt: 5.8.1 Loosen the two screws (a) on the beltguard, then remove the beltguard, keeping the screw assemblies captured on the beltguard. 5.8.
VP 1340/VP 1550 5.9 Maintenance Exciter Lubrication See Graphic: wpmgr006018 The bearings in the exciter assembly are splash lubricated and rotate at very high speed. It is important to maintain the exciter oil at the correct level and change it regularly. Check oil level in exciter every 50 hours of operation. To check oil level, place plate on a flat, level surface. Remove the drain plug (a) with seal ring (b). Oil level should be at drain plug threads. Add oil as required.
Maintenance VP 1340/VP 1550 5.11 Lifting Machine See Graphic: wpmgr006023 See Technical Data for weight of the machine. To lift machine manually: 5.11.1 Stop the engine. 5.11.2 Obtain help from a partner and plan the lift. WARNING To avoid burns or fire hazards, let the engine cool before transporting the machine or storing it indoors. Turn the fuel valve to the off position and keep the engine level to prevent fuel from spilling. 5.11.3 Grasp machine by the lifting handles (a) and (b).
VP 1340/VP 1550 Maintenance 5.12 Transporting Machine See Graphic: wpmgr006043 To avoid burns or fire hazards, let engine cool before transporting machine or storing indoors. WARNING 5.12.1 Turn fuel valve to the off position and keep the engine level to prevent fuel from spilling. 5.12.2 Tie down machine on vehicle to prevent machine from sliding or tipping over. Tie machine to vehicle at points shown on graphic. wpmgr006043 5.13 Storage If plate is being stored for more than 30 days: 5.13.
Maintenance VP 1340/VP 1550 5.14 Troubleshooting Problem / Symptom Reason / Remedy Plate does not develop full speed. Poor compaction. • Engine throttle control not completely open. • Throttle control not adjusted correctly. • Ground too wet, plate sticking. Allow soil to dry before compacting. • Drive belt loose or worn, slipping on pulleys. Adjust or replace belt. Check that engine mounting bolts are tight. • Exciter bearings binding. Check condition and level of oil in exciter.
EC Declaration of Conformity Manufacturer Wacker Neuson Manila, Inc. Dasmariñas, Cavite, Philippines Product Product VP 1340, VP 1340W, VP 1340W-L, VP 1340W-LL, VP 1340W-LF, VP 1550, VP 1550W Product category Vibrating plate Product function Compacting soils Item number 0008705, 0008706, 0630001, 0630002, 0630003, 0008707, 0008708, 0630013 Net installed power 4.
Important: For spare parts information, please see your Wacker Neuson Dealer, or visit the Wacker Neuson website at http://www.wackerneuson.com/. Wichtig! Informationen über Ersatzteile erhalten Sie von Ihrem Wacker Neuson Händler oder besuchen Sie die Wacker Neuson Website unter http://www.wackerneuson.com/. Important : Pour des informations sur les pièces détachées, merci de consulter votre distributeur Wacker Neuson, ou de visiter le site Internet de Wacker Neuson sur http://www.wackerneuson.com/.
