DTU-710 SAFETY INSTRUCTIONS INTERACTIVE PEN DISPLAY WARNING Do not use DTU-710 Interactive Pen Display in a facility control system that requires extremely high reliability; it may cause other electronic devices to malfunction, or other devices may cause DTU-710 to malfunction. Where use is prohibited, power off DTU-710 to prevent the possibility of it causing other electronic devices to malfunction. Wacom does not accept any liability for direct or consequential damages.
Introduction and Overview The Wacom® DTU-710™ Interactive Pen Display combines an LCD monitor with a Wacom tablet. This gives you a direct point-and-draw-on-screen interface that can be used with a Personal Computer (PC) or Macintosh computer. DTU-710's basic components include a Wacom tablet internally mounted behind a 17.0" diagonal TFT color LCD monitor, and Wacom's pen.
Precautions on Use and Handling Be sure to follow all instructions, cautions, and warnings found within this manual. Failure to do so could cause the loss of data or damege of your computer. Failure to do so could also void your warranty, in which case Wacom shall have no responsibility for such loss or damage and to repair or replace the product. ■ Do not lift DTU-710 by the stand; this may damage the stand mechanism. When lifting or moving DTU-710, always do so by grasping the main body casing.
Table of Contents Checking Packed Components 5 Installation 6 LCD Monitor Installation Tablet Software Installation for Windows and Macintosh Customizing DTU-710 - The Basics 8 Opening the Wacom Tablet Control Panel Calibrating the Tablet DTU-710 Component Functions 10 Front View Rear View Using an Alternate Mount or Stand Using the Pen 13 Pen Using a Pen Remouing the side switch Adjusting the LCD Monitor 15 Factory Presets, Multi-Cync, and User Settings Working with OSD (On Screen Display)
Checking Packed Components In your package you will find the following items: AC Adaptor and Cable DTU-710 main unit Pen with Pen Stand USB Cable and RS-232C Cable* User's Manual Wacom Tablet CD Contains the driver software. (Windows/Macintosh) DVI-DVI Cable and DVI-VGA Cable* Some package configurations includ an additional CD containing bundled software applications. Please retain the package box for use when storing or shipping DTU-710. * For DTU-710 only. Do not use with other devices.
Installation LCD Monitor Installation First install the monitor portion of DTU-710. Do not connect the USB cable or serial data cable until you procede to the step " ". Turn off your computer. IMPORTANT: Never connect or disconnect the DVI video cable or power cable while your computer or DTU-710 is powered on. This can damage the LCD display or video card. Connect the DVI-to-DVI cable or DVI-to-VGA cable between DTU-710 and your computer. Set the DVI/VGA switch.
Connect the AC adaptor power cable and plug the adaptor into an AC outlet. Turn on the power switch of DTU-710. The power lamp will light blue, and then turns orange. Turn on your computer to start your operating system. The maximum resolution of DTU-710 is 1280 x 1024, True Color (24 bit). As necessary, configure the monitor control panel settings for the proper size and color resolution. The number of colors is constrained by the performance of your computer or graphics card.
Customizing DTU-710 – The Basics Opening the Wacom Tablet Control Panel The Wacom Tablet Control Panel makes it easy to customize your Interactive Pen Display and the pen. To open the control panel: Windows: Click on the Windows Start button and choose Programs. From the Wacom Tablet group, choose the Wacom Tablet option. Macintosh: From the Apple menu, choose Control Panels and then Wacom Tablet.
Calibrating the Tablet You will need to calibrate the tablet in order to line up the screen cursor position with the position of the pen on DTU-710. This is required to adjust for parallax caused by the display screem overlay. After setting the tablet in its working position, follow the procedure below to calibrate the tablet. From the Wacom Tablet Control Panel, select the Calibration tab. If you are working with multiple monitors, select the Monitor that corresponds to the tablet's LCD display.
DTU-710 Component Functions Front View MENU Button Opens and closes the OSD*1 menu. - (minus) Button, + (plus) Button In the OSD*1 menu, Use these buttons to select an option that can then be activated. After activating a selected option, press the + button to increase a selected item value, and press the - button to decrease it. ENTER Button MENU - N E ENTER STATUS POWER Press this button when you select or exit an item in the OSD*1 menu.
Rear View Stand Adjustment Lever Pull this lever to adjust the stand. Release the lever to lock the stand in Connector Panel Cover To remove, slide it to the right. CAUTION Be careful to avoid catching your finger in the gap of the movable portion of the stand. Stand The stand can be used to adjust the tilt angle of the unit from low (16° from horizontal) to high (72° from horizontal). IMPOTANT Be sure to adjust the tilt angle of the stand to the low tilt position before packaging DTU-710.
DTU-710 Component Functions Using an Alternate Mount or Stand If you will be using DTU-710 in an installation that requires the use of an alternate mounting platform, you can remove the adjustable stand from DTU-710 and mount the pen display onto a VESA conforming mount arm or stand. A VESA mounting platform will require mount screws that are 4 mm wide with a 0.7 mm pitch (M4 Regular). Exceeding the screw clearance depth of 15 mm will damage DTU-710 internal components.
Using the Pen Pen Hold the pen as you would a pencil. Make sure the side switch is in a convenient location where you can press it with your thumb or forefinger, but won't accidentally press it while drawing. Eraser Eeasar Second Side Switch Side Switch Tip Switch Pen Tip When the pen tip is within proximity (5 mm or 0.2 in) of the active area, the tablet reports: - The x, y coordinates of the pen tip. - The pressure applied to the pen tip. - Whether a side switch is on or off.
Using the Pen Using a Pen Pointing and Selecting Move the pen above DTU-710 screen to position the screen cursor. The cursor instantly jumps to the new location (absolute positioning). Press the pen tip on DTU-710 screen to make a selection. Note: If the screen cursor is not aligned with the pen tip, you will need to calibrate DTU-710.
Adjusting the LCD Monitor Factory Presets, Multi-sync, and User Settings Factory Presets: To display images with the best quality (based on the incoming signal), DTU-710 comes with a number of factory default standard display modes. Multi-Sync: When connected as a VGA display, DTU-710 attempts to automatically synchronize to the incoming signal. Multi-Sync functions if the horizontal frequency is between 30 to 80 kHz and the vertical frequency is between 50 to 75 Hz.
Adjusting the LCD Monitor Horizontal Center (VGA only) Select to move the screen image left or right. To automatically adjust, use the Reset option. Vertical Center (VGA only) Select to move the screen image up or down. To automatically adjust, use the Reset option. Color Provides settings for 9300°, 6500°, and 5000° Kelvin. Also provides a User option that enables you to adjust red, blue and green independently. Selecting DIRECT displays the received signal as it is without any adjustment.
Adjusting Pitch and Phase (VGA only) Some computers and video cards may not allow the multi-sync function to fully work when DTU-710 is first connected. If some portion of the text appears blurred, adjust the pitch and phase by following the procedure below. For crisp images, set the DTU-710 resolution of your video card to 1280 x 1024. From the Wacom Tablet Control Panel, select the Calibration tab. If you are working with multiple monitors, select the Monitor that corresponds to DTU-710.
Adjusting the LCD Monitor HINT (1280 x 1024 resolution under Windows only): You can also adjust Pitch and Phase in the closing Windows display. If the pitch is not calibrated, vertical moire appears in the darkened area. And if the phase is not calibrated, the darkened area riffles. Power Saving DTU-710 conforms to VESA and Energy Star power saving guidelines.
Caring for DTU-710 Cleaning To clean the DTU-710 casing, use a soft cloth with mild detergent (such as dish washing liquid) diluted with water. Do not use paint thinner, benzine, alcohol, or other organic solvents to clean DTU-710 casing or pen. To clean the display screen, use a soft, dry cloth. If necessary, slightly moisten the cloth with water and try again. When cleaning, apply only a light amount of pressure to the display screen and do not make the surface wet.
Display Troubleshooting If you encounter problems with DTU-710 display, refer to the following tables. Your problem may be described here, and you can try the solution offered. For the problems regarding tablet or pen, refer to the Troubleshooting chapter in the online Help that can be accessed from the Wacom Tablet control panel. Genera Problem The message "OUT OF SCAN RANGE" appears. ■ ■ ■ ■ Hint The input signal frequency is incorrectly set or not compatible with DTU-710.
General Problem Hint The image appears multiple times Do not extend the video cable. Do not use an input selector switch box. on the display. The color white does not display as ■ white. ■ Be sure the DTU-710 color profile has been installed and is selected as the profile for use with your operating system and applications. Verify also that the display is operating at the factory default settings. If that is not sufficient, then adjust color as necessary.
Obtaining Technical Support If you have a problem with DTU-710, first check the appropriate setup chapter in this guide to make sure the unit is installed correctly. Then review the Troubleshooting section within this manual and the online Help; your problem may be described there and you can try the solution offered. You can also check the product FAQs (Frequently Asked Questions) on the Wacom web site.
Specifications General Specifications Physical dimensions (WxDxH): Weight: Main Unit input Voltage: Power consumption: Operating temp. & humidity: Storage temp. & humidity: 418x362x57mm (excluding the stand) 5.8kg (including the stand) DC12V 45W or less (DC12V) 5 to 35 deg. C, 80%RH (non condensing) 10 to 60deg. C, 90%RH (non condensing) (maximum storage humidity is 38% at 60 deg.C, and maximum storage temperature is 42 deg. C at 90% humidity) LCD Display Display: Screen size: Resolution (75Hz Max.
Specifications Power Adaptor Input voltage: Output voltage: 100 to 240 VAC, 50/60 Hz 18 VDC, 2.5 A Pen (UP-911E) Pen tip travel: Eraser tip travel: Physical dimensions, weight: Side switch type: 0.1 mm (0.004 in) or less 2 mm (0.08 in), approximately 14.0 x 159.0 mm, 16g (0.63 x 6.26 in, 0.56 oz) Rocker switch Pen Accessories Extra nib: Pen holder: PSI-A021 PST-A026 24 DTU-710_EN.indd 24 04.7.
DTU-710_Manual.fm Page 44 Thursday, August 26, 2004 5:51 PM RADIO AND TELEVISION INTERFERENCE The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used properly – that is, in strict accordance with Wacom instructions – it may cause interference with radio and television reception.
