Instruction Manual LCD Signature Tablet STU-520A Ver. 1 26 Sep, 2010 WACOM Co.
WACOM Co., Ltd. Table of contents 1. SCOPE ...........................................................................................................................................................2 2. SUMMARY .....................................................................................................................................................2 3. PRECAUTIONS ON USE AND HANDLING .................................................................................................2 4. OPERATION ..
WACOM Co., Ltd. 1. Scope This instruction manual applies to the LCD Signature tablet STU-520A. 2. Summary The Wacom® STU-520A LCD signature tablet combines the benefi ts of a liquid crystaldisplay (LCD) with the control, comfort, and productivity of Wacom’s cordless, batteryfree pen technology. This gives you a direct pen-on-screen interface that leads to a truer pen-on-paper writing experience. The basic components of the LCD signature tablet include a Wacom pen tablet internally mounted behind a 4.
WACOM Co., Ltd. tablet may damage the display screen or other components. Do not put heavy articles on the LCD signature tablet or push against it with a strong force; This may damage the display screen. Do not place heavy articles on the STU-520A cabling, repeatedly bend the cables sharply, or apply heavy stress to the cable connectors; this may damage the unit or cabling. If the pen tip becomes sharp or angular, it may damage the coating on the display screen. Please replace the pen tip if necessary.
WACOM Co., Ltd. “Cet appareil numérique de la classe (B) est conforme à la norme NMB-003 du Canada.” Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
WACOM Co., Ltd. 5. Product specification 5-1 General Specifications Main body exterior color Size Mass Pen holder Main body fixation Status display Power Supply Voltage Black 160.0mm(W) X 177.3mm(D) X 15.5mm(H) 300g Tray and penholder hole Bottom fixation hole LED +5V DC Power Consumption 2.
WACOM Co., Ltd. 5-3 Coordinate Coordinate Specifications Technology Active Area Maximum Coordinate Resolution Coordinate Accuracy Accuracy Assurance Height Reading Height Tilt range *1) Pen pressure Maximum Report Rate *2) Electro-magnetic resonance technology 103.92 x 60.48 mm (X)10400 (Y)6048 0.01mm(2540ppi) ±0.
WACOM Co., Ltd. 5-7 Environmental Conditions Ambient Temperature Relative Humidity Operation +5C ~ +35C Storage -10C ~ +60C Operation 20 ~80%(noncondensing) Storage 20 ~90%(noncondensing) 6. Accessories 6-1 Accessory List (STU-520A) Parts number QTY USB cable(1.
WACOM Co., Ltd. 6-2 Pen Specification NAME MODEL NUMBER REMARK Main body UP-610-88A-1 Electronic pen Physical dimensions Φ9×140.
WACOM Co., Ltd. 6-3 USB cable(STJ-A299) NAME MODEL NUMBER Length color TYPE USB Cable STJ-A299 1.
WACOM Co., Ltd. 7. Fixing STU-520A STU-520A can be fixed on the table etc. Please refer for fixing STU-520A. The following; wood screw is recommended for fixing. Φdk Φk K L Φdk: 4 ~ 5.8mm K: Less than 2mm L: 10mm is recommended (more than 10mm) Φd: 2 ~ 3mm a) Screw wood screws to the table etc. by following dimensions. Note) Screwing will be easier by pre hole for screwing. 3.
WACOM Co., Ltd.
WACOM Co., Ltd. b) Put STU-520A on the table and screws are match with fixation hole of STU-520A Please make sure that STU-520A isn’t lifted up or stressed. It may cause of damage of inside or case. Note) If STU-520A is stressed or tight, don’t force to fix. Please adjust height of screws again. Bottom of STU-520A b) Pull STU-520A to forward and fix. Note) If STU-520A is stressed or tight, don’t force to fix. Please adjust height of screws again.
WACOM Co., Ltd. 8. Replacing the pen tip The pen tip (nib) can wear with normal use. In the unlikely case that the nib gets too short or develops a sharp edge, you can replace it with spare nibs. To remove the old nib: To insert a new nib: Clasp it with a pair of tweezers, needle-nosed Slide it straight into the barrel of the pen. plier, or similar instrument and pull the old nib Firmly push the nib until it stops. The new nib straight out of the pen. will slide into the correct position.
WACOM Co., Ltd. 9. How to install pen tether For avoiding drop or lost the pen, using the pen tether which came with the pen is recommended. a) Thread the end of the pen tether through hole of pen top. And Thread the other end of the pen tether through a lope of opposite pen tether end. b) Thread the end of the pen tether through the pen tether hole on the back side of STU-520A. And thread the pen through the end lope of the pen tether.
