ELECTRIC FLAT PANEL FIREPLACE - NO HEAT OWNER’S MANUAL Decorative Log Bed Decorative Pebbles Decorative Crystals AC 120V 60Hz 1 2 W WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. CAUTION Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.
IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this electric fireplace! DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord away from traffic area, and where it will not be tripped over. Connect to properly grounded outlets ONLY.
ALWAYS check your electric fireplace cord and plug connections with each use! i) MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat. ii) electric fireplaces draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
Parts and Hardware A – Fireplace ( 1 ) B – Wood Screws ( 5 ) C – Drywall anchors (5 ) D – M4x8 Metal Screws (2) RC – Remote Control E - Wall Bracket (1) F - Decorative Crystals I - Shelf G - Decorative Crystals H - Decorative Log bed Installation and Assembly Rear View of Fireplace Minimum 0” (0 cm) 0” (0 cm) 0” (0 cm) Minimum 0” (0 cm) Step 1. Find a safe location. Minimum clearance on each side: 0” (0 cm). Minimum clearance below: 0” (0 cm). Minimum clearance above: 0” (0 cm).
NOTICE The wall mount fasteners included with this fireplace are for use ONLY with a wood-framed wall covered in drywall (sheet rock). For concrete walls, cinder blocks, or other wall types, consult a professional for the best attachmentmethods. ALWAYS unplug this fireplace electric fireplace before assembly or cleaning, or before relocating. Failure to do so could result in electric shock, fire, or personal injury. Drywall Studs STEP 2. A. Locate the wall studs using an electronic stud-finder.
STEP 3. Drill a pilot hole into each mark using a 1/4” wood drill bit. A. If screws will go into three studs, no drywall anchors are needed. B. Tap the drywall anchor(s) (C) carefully into the drywall holes until they are flush with the drywall surface. Use care to avoid damage. E E B B B B B B B B STEP 4. Align the holes in the wall bracket (E) with the pilot holes and drywall anchors.
STEP 5. A. With the help of a capable adult, lift the fireplace (A) and align the hooks on the back of the fireplace with the slots on the wall bracket. Carefully set the hooks into theslots. B. Secure the fireplace to the wall bracket with two M4x8 metal screws (D), one on each side. Thread the screws through the fireplace and into the wall bracket side tabs. Tighten bothscrews with a Phillips screwdriver. The unit may now be plugged in.
Decorative Log Bed -H NOTE: The fireplace comes with the Decorative log bed, Crystals and Pebbles, To make switching please follow these steps. Have a capable adult help you. STEP 6A. While one person holds the glass panel, remove the two screws at the top edge of the fireplace with a Phillips (+) screwdriver. STEP 6B. Together, carefully remove the front glass panel and set it aside on a clean soft surface. STEP 6C.
Operation Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death. Power Make sure the ON/OFF switch, located on the left side panel, is in the OFF position. Plug the power cord into a 110~120 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not loose.
TIMER button: Controls timer settings to turn off fireplace at selected time. TIMER Settings range from 0.5 hours to 7.5 hours. 2. Press again until desired setting is reached. Indicator lights show setting. FLAME button: Makes flame effect dimmer and brighter. FLAME NOTE: Flame effect stays on until power button is turned off. Flame effect must be on for electric fireplace to turn on. COLOR button: Makes the color flame effect changing. COLOR 1. Press once. Indicator light turns on. Timer is set to 0.
DO NOT use brass polish or household cleaners as these products will damage the metaltrim. Glass: Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper towel or lint-free cloth. NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch thesurface. Vents: Use a vacuum or duster to remove dust and dirt from the electric fireplace and vent areas.
Troubleshooting ! WARNING DISCONNECT THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. Problem Possible Cause Solution 1. Flame is not moving. 1. Loose wiring. 2. Flame motor defective. 1. Inspect wiring for loose connections. 2. Call a qualified service technician to replace flame motor. 3.Flame rod out of place 3."Flame Rod" out of place due to rough transit/handling of the product.
