Moe that yr new product has bes delivered © VOL, hel VO Huguenot BY EEE BI sb Vol Can BRI TE TUN STEP Opa the packaging af the vnd whine ths handle land identify elaboration ol the upholstered mainframe the packing.
STEP 4 Remove the components from the protective material and place anathema clean, flat and leveled surface, this is important; The box should contain the following pieces: 2x Side frames (Al End frames is) 1x Cover (E} ix Hardware (F) pack 15x slave {0} impairment Beheading on the size of the platform bate you purchased, your carton will contain: Single ¥L & Twin & Full: He center rail Queen: 1x Center rail {C) Viking Bi CA King 2x Center rail (C)
STEP 3 identify the content of the Hardware pack (Fl: dle (H) 4x Corner Brackets (1) 2x Headboard bracket (K} depression: Depending on the size of the platform bate you purchased Single XL & Twine & Full: No support leg U) or Center roll bracket 11) Queen: 1x support leg (1) and 2x Center rail bracket {L) King & CA King: 2x support leg [J] and 4x Center rail Bracket (L}
4x Carriage bolts (0) Ax Flat washers (PR) Ax Nuts [0] 2x Wood screws (R) 1x Spanner [5] Ix Allen key [1] Tania an Depending on the size of the platform Bose you purchased Single XL & Twin & Full 20x Bolts (M) and Washer IN) Queen: Jox Bolts (M1 and Washer (N) King & CA King: 36x Bolts (M} and Washer [N) IMPORTANT MOTE Do nat use a power teal Lo assemble this product as il could carnage the thread of the hardware and affect the solidification of the product,
STEPS Mow that vou have identified all components, we can start the assembly process but first, pay close attention to the following detail IMPORTANT NOTE The McCormick brackets ave fitted with round holes and rounded rectangle holes.
STEP 7 FUR QUEEN AND KING SIZES ONLY Lie the Holt (M) and washer (N] to attach the center rail bracket (Tito the end frames (8). The bracket must be installed upward as illustrated Below.
STEPS Attach the 4 corner brackets {1] tithe 2 end frames (B with the bolts (M] and washers (N] using the rounded rectangle holes. Do aot fully tighten the insults at this stage, leave the loose. The bottom of the corner bracket is fitted with a plate where thee legs will attach pn: Inkiness wi position this bracket so the plate 5 at the same jewel to the bottom of the frame.
Attach the side frame: (A) to the end frame (B) using bolts (M) and washers (N) Leave the bolt footie; donor Daughter this stage of the assembly
Step 10 Complete attaching all frames but leave all bolts lopes STEP U1 Adjust each corner so the end on the side frame {A} correctly lines up with end of end frame (8B) then tighten the bolts.
Put the frame on its side and attach the legs (Hi wo the corner brackets base One all 4 legs have beer attached please re-chapel that all Bolt are evenly tighten,
RH FOR QUEEN AND KING SIZES ONLY Take the center tall {[C) and the support leg (J) Locate the attachment screws on the center rail Attach the support leg (1) to the center mil using the bolts [M}) ard washers (N).
STEP 14 FOR QUEEN AND KING SIZES ONLY Once the support leg is attached to he center rail, place the center rail In the center tall brackets,
STET IS Thiamine wooden slat (D) 1s fitted with holes which will be used to attach it to the side frames.
Lie a Phillips [star head) screw driver to attach the riddle slat to the side frames using the wood screws (R) Your new platform base can now be covered.
LAST STEP Use the cover (E} to recover the frame snd voila, your new foreplay base is ready for use, ENJOY
OPTIONAL STEPS FOR HEADBOARD Should you decide bo ise your new platform base with § headboard, the required hardware is already provided with the pack you received, STEP: Take the headboard bracket (1) provided with the hardware pack of your base and identify which holes on the bracket corresponds to the attachment holes on your headboard.
a4 sere: Hitachi the Roadbed Bracket [00 to the end frame [B) that ls deadly fitted with per-drilled holes using the bolts (M] and washers (MN). Adjust the height of the brake by sliding it up of down, Once at the desired height. make sure the bracket is straight and tighten the obis.
ester: You car slide the vicarage bolt side ecocide to fit Into the head Board attachment holes after removing the nut and washer Nice the headboard (not Illustrated) is in place, use the spanned (51 10 tighten ito the headboard brackets using the Washers (P) and nuts (0) ENJOY