Owner Manual

ManualsBrandsWade Logan ManualsFurnitureWingler TV Stand for TVs up to 85"

P.1

Assembly Instructions

Summary of content (32 pages)

PAGE 2
General Assembly Guidelines I. Ensure that all parts and hardware are available before beginning assembly. II. Follow each step carefully to ensure the proper assembly of this product. III. Two people are recommended for ease in the assembly of this product. IV. The three main types of hardware used to assemble this product are: wood dowels, screws and bolts. The provided glue is to secure wood dowels in place.
PAGE 4
Hardware List A Ø8x30mm Wooden dowel 36 pcs B Ø6x32mm Cam bolt 48 pcs C Ø15x9mm Cam lock 51 pcs Sticker 51 pcs D E Ø6x15mm Bolt 8 pcs F Ø6x30mm Bolt 4 pcs G Flat washer 12 pcs H Lock washer 12 pcs J Plate 4 pcs K Shelf support pin 8 pcs Handle Bolt 10 pcs M Handle 2 pcs N Handle 6 pcs P Europe hinge 4 pcs Bolt 24 pcs Screw 28 pcs L Q Ø4x18mm Ø4x12mm R S Ø4x25mm Screw 18 pcs T Ø3x15mm Screw 4 pcs U Ø6x30mm Bolt 1 pc V M4 He
PAGE 6
Step 2 B B B T B A B T W 1 W A B 13 x 4pcs B A B CC 19 x 3pcs 10 x 2pcs A Insert wooden dowel (A) to parts (10,13)，wooden dowel (CC)to part (19) ,then secure cam bolt (B) into part (1) , then using screw (T) attach door stopper (W) to part (1) with Philips head screwdriver as per diagram. All rights reserved. P.
PAGE 9
Step 5 F H G A A A J B B V F H G A 11 B X2 J B Insert wooden dowel (A) into part (11) ,secure cam bolt (B) into parts (11) with Philips head screwdriver ,then using bolt (F) with lock washer (H),flat washer (G)secure plate (J) to part (11) with hex key (V) as per diagram. All rights reserved. P.
PAGE 13
1 Step 9 G H 2 3 E J G V C C 11 2 C C J G HE J HE G H E C C 11 C C J G HE V Using cam lock(C) secure part (11) to part (2) with Philips head screwdriver .and using bolt (E) with lock washer (H),flat washer (G) secure plate (J) to part (2) with hex key (V) as per diagram. All rights reserved. P.
PAGE 16
Step 12 N B L N B 17 DD L B B N N B L 23 B DD B B L X2 Secure cam bolt (B,DD) into parts (17,23) ,then using handle bolt (L) attach handle (N) to parts (17,23) with Philips head screwdriver as per diagram. All rights reserved. P.
PAGE 20
1 Step 16 2 17 C 14 C 3 19 15 C 23 C 21 20 19 X2 Using cam lock(C) secure part (23) to parts (20,21) ,part (17) to parts (14,15) with Philips head screwdriver as per diagram. All rights reserved. P.
PAGE 23
Step 19 5 4 3 K K K 9 K 9 K 9 Insert shelf support pin (K) into parts (3,4,5) as per diagram. Make sure you place the four shelf support pins (K) in the same level. So the shelf is not titled .Put part (9) into unit as per diagram. Tilt and rest the adjustable shelf (9) onto the shelf support pins . All rights reserved. P.
PAGE 24
Step 20 Q Q P P Q Q L 25 L P P L 26 L M M Using screw (Q) attach Europe hinge (P) to parts (25,26) ,then using handle bolt (L) attach handle (M) to parts (25,26) with Philips head screwdriver as per diagram. All rights reserved. P.
PAGE 26
Step 22 Q 5 26 P Q 5 Q P 26 Using screw (Q) attach Europe hinge (P) into part (5) with Philips head screwdriver as per diagram. Open and close the doors .If necessary adjust the screws for a good fit . All rights reserved. P.
PAGE 27
Step 23 OR 17 23 23 Insert the assembled drawers into the unit frame, extend the Ball Bearing Slide Tracks on the pedestal Side Panel all the way forward .Then align the Slide Runners on the assembled drawers with the Slide Tracks and push the drawer carefully inside until it stops. Note : if the drawer does not go in smoothly, please take it out and repeat the step.
PAGE 30
1 Step 26 2 3 WARNING Serious or fatal injuries can occur from furniture tipping over. To prevent the furniture from tipping over we recommend that it is permanently fixed to the wall. Wall anchor and hardware are included with this product. Please make sure hardware is suitable for your walls before installing, as different wall materials may require different types of anchors. Wall AA Z Y Using screw (Y) attach Velcro strap (Z) into Nut (AA) to wall with Philips head screwdriver as per diagram.