Assembly Instructions ASSEMBLY RATING The Assembly Ratings o S-point system that shows the degree df effort needed in assembling a specific product (with 1 being easy and 5 being difficult). For most products, two persons are recommended.
90-DAY LIMITED REPLACEMENT PARTS WARRANTY This item comes with a 90-day limited replacement parts warranty to the original purchaser of new products against defects in materials and workmanship for a period of ninety (90) days from the date of receipt. This warranty 1s not transferable.
PARE & CARE ADVICE FOR YOUR FURNITURE TO LAST, CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY. PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE. BASIC ASSEMBLY TECHNIQUES Ei lis Highly recommended that the assembly should be doe near the area of its intended location. Make sure you have though space lo move around diffing the assembly. ALWAYS have at least wo people to help with transposing and assembling the product avoid any potential injury undercarriage.
PER-ASSEMBLY INTRODUCTION Unless you are particularly adept at assembling furniture, we understand building ready-to-assemble furniture can bea frustrating experience foursome. To help avoid confusion and to make the ‘assembly process quicker and smoother, we have provided some helpful tips. Before you begin the assembly, please read the following: 1. [Due tithe weight on most of the ready-to-assemble furniture, iris highly recommended that the assembly should be done near the area of iis intended location.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS Note: Every cam lock bolt must have a cam lock connector in order to fasten the parts together. 1 Align the cam connector with its Secure the threaded I side opening (or arrow) end of the cam bolt pointing to the small by using a drilled hole. screwdriver. or Turn right (clockwise) to tighten. Two parts should fit snugly (3) against each other. Insert the cam lock bolt into the per-drilled hole above the cam connector.
SHOE CABINET ASSEMBLY INSTRUCTIONS please keep for future reference PARTS LIST © irc © rc irc irc @irc @irc © PCs @ orcs @rc @irc @1rc TTT T Le DIMENSIONS : © rc Before vou begin; please read “Assembly and Care 0] 1PC @ 1PC Advice! “Pr-Assembly Introduction” and “Cam Lock Fastener Assembly: Instructions™. HARDWARE LIST Mercedes (DD mercers (3) res @ apes GPC ® specs al, (8x20) (8x30) . @ epics PCs (TSETSE (0 SETS @) SETS (D SETS 16° cto a P.
SHOE CABINET Get Ready. Please group boards as below.
ASSEMBLY INSTRUCTIONS STEP x 2 Use a dab of glue into dowel holes before inserting dowels on the following panels in the diagram. / 7 hole) Hardware 2) x 3 pcs Refer to page 5 on how to secure cai locks (#2) onto tam bolls STEP: 3 Hardware (2x 3 pcs Grooves of panels (#C, B,D} are located towards the bottom.
ASSEMBLY INSTRUCTIONS STEP : 4 Hardware (F)x 8 pcs Use Tonier screws (£7) on steps STEP: 5 Hardware (2) x 4 pes Attach panels (#M) 10 panels (#N) together, then attach and secure them to the! bottom of the product as shown in the diagram, Page 10 of 14
ASSEMBLY INSTRUCTIONS STEP: 6 Hardware 44) x 6 pcs Tap {loot protectors (#14) to the bottom of the product by using 4 hammer. STEP: 7 Hardware (2)x 6 pcs Align and insert back panels to the grooves of the product. Make sure the back panels are fully flushed within the grooves of the product.
ASSEMBLY INSTRUCTIONS STEP: 8 Hardware § x 12 pcs Insert shelf pins (£8) to the desired height of the shelves (HI.
ASSEMBLY INSTRUCTIONS STEP : 10 Hardware © x 4 sets Please refer to last page for hinge adjustment. For safety reason, this item has been STEP : 11 supplied with wall straps. We highly recommend securing the item to the Hardware {3x 8 sets wall using the supplied hardware Hardware §2x 2 sets and straps to prevent tip-over Make sure the unit is rested on a flat surface and does not feel loose or wobbly. If it does, double check all bolts/screws are secured and properly tightened.
Height Adjustment Two screws, located at the top and bottom of the hinge. mount the hinge to the cabinet Turn these first to make sure the door is secure. If the door is:still too high or low, loosen these screws slightly and then lift or lower the door until it is in the position you want. Firmly tighten the screws to secure the door. Remember to opportunistically you loosen these screws or it could drop completely out of its initial position. Close the cabinet doors to see whether the fit is satisfactory.
