ASSEMBLY INSTRUCTIONS TOOLS REQUIRED Philips Screwdriver {Not Included) Persons Recommended 000 EASY movement DIFFICULT Thai Assembly Rating is a S-point system showing the level of effort needed to assemble a specific product, 1715
CHECK BEFORE STARTING Are you missing anything? Double-check afl parts, hardware and accessories sifted on Page 6 are accounted for Check out our Quick Tips! We recommend reviewing the per-assembly handouts. Even experts need a refresher now and then! Prep Time! Please review the assembly instructions and ali diagrams prior to assembling. Arrange pairs as recommended on Page 7 and group identical hardware together to make assembling easier.
PRE ASSEMBLY INTRODUCTION We understand building ready-to-assemble furniture can bie a challenging experience for some. To help avoid confusion, we have provided some helpful tips that may speed up the process. Teamwork ALWAYS have at least two people tw help with transporting and assembling the product to avoid potential injury and/or damage. Suitable Location Assembling near the area of the intended location is highly recommended.
ASSEMBLY AND CARE ADVICE A FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. 4 \ Turn clockwise tg tighten and only tighter whee step is completed or when instructed fo do so. Position each part correctly and insert screws or bolts into their respective holes. Use the appropriate hand tools ar prows tools for assembly. Select steps, such as lightening resews and/or bolts, may require hand tools to avoid causing damage during assembly.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS Note : £3 Every cam lock boil must have a cam RR ND rock connector in order to fasten the parts together. cam bolt cam lock screwdriver Screw the cam insert the cam bolt into the bolt inch panel. bicycle hale of joint panel. eee er” Align the cam lock with its side opening Turn the cam lock clockwise gently {or arrow} pointing 10 cam bolt. until it will not turn any more.
COFFEE TABLE » Please cheap instructions for future reference. « Check the ubiquity and regularity of pairs dnd hardware before you start.
ASSEMBLY INSTRUCTIONS Insert dowel (4C) 10 the hole of the divider panel Align the divider panel {if4) to the holes of the shelf frame Secure by using screws (1H). 1 Part) x1pc Part «pe Hardware@0) expo Hardware) PCs iL RS Tip: Place parts on the flat level surface to ease alignment and assemble.
ASSEMBLY INSTRUCTIONS 3 Part x 1pc Hardware@n) PCs Hardware§g) PCs Hardware§o) x1pc Hardware) apexes 4 Part(®) x 1pe Hardware C) expel Hardware) PCs Attach cam bolts (#A) and dowel (4C) onto shelf frame Align bottom panel (#5) to the shelf frame (52), then secure by using cam locks ‘Attach dowel (2C) ta the hole of the bottom panel Align large bottom panel (#3) to the bottom panel then secure hy using screws 8/15
ASSEMBLY INSTRUCTIONS “Attach cam bolts (8A) and dowels (40) to the holes of the legs Align logs, to the holes of the product, then secure by using cam locks 5 Part(®) x 1pc Part@x 1pe Hardware@s) apexes Hardware@) x poss Hardware) apexes to the holes of the product. Secure by using cam lacks (#13) 6 [Attach cam bolts (#A) and dowels (#C) to the holes of the legs Align legs (47.8) pe Part(#) x pc Hardware@a) Apexes Hardware) x PCs Hardware) PCs Flip the product 180 degrees.
ASSEMBLY INSTRUCTIONS 7 Part) pe Hardware) apexes Part 1pe Hardware@3) x10pes Slightly hammer in Door protectors (#L) to the bottom of each legs.
ASSEMBLY INSTRUCTIONS Attach dowels (#0) 16 the holes of the top panel {#1} Align top panel (41) io the holes of the base. 0 Secure by using cam Jocks (#K3, then use stickers (#8) to cover cam locks (9K).
11 ASSEMBLY INSTRUCTIONS Attach cam bolts (#D) to the holes of the front drawer panel Align front drawer panel (#9) to the holes of the side drawer panels Secure by using cam locks Part) PCs _#D Hardware) spots #9 Ey. Hardware E) PCs Slide the bottom panel (#11) through the thin lined gaps of the drawer.
ASSEMBLY INSTRUCTIONS Insert dowels (#F) to the holes of the drawer bottom support Almach drawer bottom support (#12) to the holes of the drawer back panel.
