Owner Manual

ManualsBrandsWade Logan ManualsCeiling LightsBradburn 1 - Light

INSTALLATION INSTRUCTIONS

Please read carefully and save these instructions, as you may need them at a later date.

CAUTION

Risk of Fire. Consult a qualified electrician to ensure correct branch circuit conductor.

Minimum 90°C supply conductors.

Turn off the main power at the circuit breaker before installing the fixture, in order to

prevent possible shock.

GENERAL

All electrical connections must be in accordance with local and National Electrical Code

(N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain

the services of a qualified electrician.

Remove the fixture and the hardware package from the box and make sure that no parts

are missing by referencing the illustrations on the installation instructions.

ASSEMBLY AND INSTALLATION

LED CEILING FLUSH MOUNT

1. Outlet Box

2. White Supply Wire

3. Black Supply Wire

4. Supply Ground Wire

5. Mounting Screws

6. Wire Nut

7. Black Fixture Wire

8. White Fixture Wire

9. Fixture Pan

10. Fixture Ground Wire

11. Acrylic Shade

12. Frame

13. Thumb Nuts

14. CCT Switch

1. Thread the mounting screws (5) halfway into the outlet box (1).

2. Pull the power supply wires out from the outlet box (1). Connect the black

supply wire (3) to the black fixture wire (7) using a wire nut (6). Connect the

white supply wire (2) to the white fixture wire (8) using a wire nut (6). Connect

the fixture ground wire (10) and the supply ground wire (4) together using a

wire nut (6). Wrap all wire connections with electrical tape for a more secure

connection. Carefully tuck all the wires and wire connections into the outlet box

(1).

3. Place the fixture pan (9) over the outlet box (1) and feed the mounting screws

(5) through the keyhole slots. Twist the fixture pan (9) so that the mounting

screws (5) slide into the narrow slots of the keyhole slots.

4. Tighten the mounting screws (5) so that the fixture pan (9) is secured flush

against the ceiling.

5. Set the CCT switch (14) to the desired color temperature.

6. Secure the acrylic shade (11) and the frame (12) to the fixture pan (9) using the

thumb nuts (13).

Summary of content (4 pages)

PAGE 1
LED CEILING FLUSH MOUNT INSTALLATION INSTRUCTIONS 1 2 5 3 4 Please read carefully and save these instructions, as you may need them at a later date. 6 CAUTION 8 Risk of Fire. Consult a qualified electrician to ensure correct branch circuit conductor. Minimum 90°C supply conductors. 7 10 9 Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
PAGE 2
LUMINARIO LED DE TECHO INSTRUCCIONES DE INSTALACIÓN 1 2 5 3 4 Por favor lea cuidadosamente y guarde estas instrucciones, puede necesitarlas posteriormente. 6 PRECAUCIÓN 8 Riesgo de incendio. Consulte a un electricista calificado que le garantiza el uso de conductores adecuados para el circuito. Conductores suministrados con un mínimo de 90ºC. 7 10 9 Desactive la electricidad del cortacircuitos antes de empezar la instalación de la lámpara para evitar una descarga eléctrica.
PAGE 3
PLAFONNIER DEL GUIDE D’INSTALLATION 1 2 5 3 4 Veuillez lire ces instructions attentivement et les conserver pour pouvoir vous y référer au besoin. 6 MISE EN GARDE Afin d’éviter tout risque d’électrocution, veuillez couper le courant au niveau du disjoncteur avant d’installer le luminaire. 8 7 10 9 GÉNÉRAL Toutes les connexions électriques doivent être effectuées conformément aux règlements locaux et aux normes du code national de l’électricité.
PAGE 4
FCC NOTICE AVISO DE LA FCC ADVERTENCIA: Cambios o modificaciones a esta unidad no aprobados expresamente por la parte responsable del cumplimiento podrían anular la autoridad del usuario para operar el equipo. WARNING: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.