Owner Manual

ManualsBrandsWade Logan ManualsBronze Blades Ceiling Fans52'' Gatto 3 - Blade LED Propeller Ceiling Fan with Remote Control and Light Kit Included

a. Fan blades (3)

b. Ceiling mounting bracket

c. Canopy

d. Canopy cover

e. Ball/downrod assembly

f. additional downrod

g. Coupling cover

h. Fan motor assembly

i. Light pan

j. LED light kit

k. Light shade

l. Remote control set

m. Balance kit & Accessories bag

1. Programming code maching mode is used between emitter and receiver, Turn "ON" the

supply power within 30 seconds and press the emitter's "STOP" button for 5 seconds, after

hearing a long sound “BEE”, press “1H” button. It can load normally after hearing the "BEE"

which means programming successfully

and it can works normally.

(PS: Programming mode is not acepted after turn "ON" the supply power for 30 seconds)

Fan not control.

Step 1. Loosen the screws on the fan hanger and fix the

fan hanger to the ceiling outlet box with wood screws.

Pass the 120-volt supply wires through the center hole in

the ceiling fan hanger.

Step 2. Remove the pin and clip from the downrod. Then

partially loosen the two set screws in the yoke at the top of

the motor assembly

Step 3. Slip orderly the canopy, canopy cover and

coupling cover onto the downrod upwards; and then feed

the lead wires from fan motor pass through the downrod.

Step 4. Install the downrod into yoke. Slide the downrod

into the yoke at the top of the motor assembly. Align the

holes. Insert the Hitch Pin through the downrod and then

re-install the retaining clip; then tighten the set screws.

Step 5. Place the downrod ball into the hanger bracket

socket. Rotate the entire assembly until the "Check Tab"

has dropped into the "Registration Slot" and is seated

firmly. The entire motor assembly should not wobble

(left or right) when seated properly.

WARNING: Failure to reattach the cross pin and seat

the "Check Tab" can cause the fan to fall from the

ceiling during operation. Take special care to make

sure this pin is reattached.

CHANGING THE DOWNROD (OPTIONAL)

NOTE: Your fan comes with an additional downrod in case the ceiling is higher. In this case, perform

the following steps for correct installation:

1. Remove the hanger ball from downrod by loosening the set screw at the top of the downrod which

holds the hanger ball to the downrod.

2. Slide the hanger ball down the downrod and remove the support pin.

3. Insert the support pin in the

holes at the top of the downrod and slide the hanger ball up the

downrod. Make sure the support pin is properly seated in the grooves in the top of the hanger ball.

4. Tighten the set screws firmly.

WARNING: To prevent the fan wobble and serious injury. Make sure to attach the support pin

properly and tighten the set screws firmly.

6.. ELECTRIC CONNECTIONS

WARNING: To avoid possible electrical shock, be sure

you have turned off the power at the main circuit panel.

Follow the steps below to connect the fan to your

household wiring. Use the wire connecting nuts

provided with your fan. Secure the connectors with

electrical tape. Make sure there is no loose wire strand

or connection.

STEP 1. Insert the receiver into the ceiling mounting bracket

with the .at side of the receiver facing the ceiling. For best

performance, make sure the White Antenna, on the end of

the receiver, remains extended and not tangled with any of

the electrical wires.

STEP 2. Motor to Receiver Electrical Connections:

Connect the colorful wires (3) from receiver with the colorful

lead wires (3) from fan motor, follow the corresponding rules

as below: black to black, blue to blue, white to white.

Secure each set of wire connections with the wire nuts

provided in the parts package.

STEP 3. Receiver to Supply Wires Electrical Connections:

Connect the black wire from the ceiling outlet box to the

black wire marked "AC in L" on the receiver. Connect the

white (neutral) wire from the ceiling outlet box to the white

wire marked "AC in N" on the receiver. Secure each set of

electrical connections with the plastic wire nuts provided in

the parts bag.

STEP 4. Connect the ground wire (green or bare copper)

from the outlet box to the ground wire on the ceiling

mounting bracket and the ground wire from the ceiling fan.

After finishing all connections, separate the white and green

wire connections to one side and the black wire connections

to the other side of the outlet box.

NOTE: Fan must be installed at a maximum distance of

30 feet from the Hand-held Remote Transmitter for

optimal signal transmission between the transmitter and

the fan's receiving unit.

7.. INSTALL CANOPY AND CANOPY COVER

Tuck all connections neatly into ceiling outlet box.

Slide canopy up to mounting bracket and place one of key hole slots over the mounting screw on mounting

bracket.

Rotate canopy until screw head locks in place at narrow section of key hole.

Slide canopy cover up to the bottom of canopy and turn it along the grooves until locked in place.

8.. INSTALL FAN BLADES

Align the holes on blade and screw holes on base plate and motor. Install the blade to the motor with the

blade screws provided. Repeat this process with the other blades.

9. INSTALL LED LIGHT KIT AND LAMP SHADE

Step 1. Connect the wires from light with the wires from the fan assembly by male and female

connectors. Install the light pan on the base plate of motor assembly by three screws pre-assembled on

the base plate.

Step 2 .Raise and hold the glass shade close to the light pan, turn glass shade clockwise until it locks in

place. Make sure to tighten the glass shade firmly.

Slide the forward/reverse switch

on the top of motor assembly to

get desired airﬂow direction.

Reverse function

Battery for emitter: 2 x 1.5V AAA

Color temperature adjustment

This LED Light Source has three color temperatures: 3000K,

4000K, 6000K.

Pressing the LIGHT button on the remote control turns the light

on at its default color temperature. To change the color

temperature, use the LIGHT button to turn off the LED light

panel and then press it again within 5 seconds to turn the light

back on at a new color temperature.

Leave the light on for more than 5 seconds before turning it off.

The current color temperature will be stored as the new default

setting.

10 . OPERATION FOR REMOTE

11. TROUBLESHOOTING

12. CUSTOMER SERVICE