ELECTRIC FLAT PANEL FIREPLACE HEATER OWNER’S MANUAL AC 120V 60Hz 1500W WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. CAUTION Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.
IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
For residential use only! NOT for commercial use! Any commercial or public use of this heater voids all warranties, and could cause injury. This product is not intended to be a primary heat source. It is for supplemental heatonly. INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock! Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! NEVER modify this heater. Doing so could result in personal injury or property damage.
Preparation This product includes a GLASS panel! Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage. Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grouped for wall-hanging use. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.
NOTICE The wall mount fasteners included with this fireplace are for use ONLY with a wood-framed wall covered in drywall (sheet rock). For concrete walls, cinder blocks, or other wall types, consult a professional for the best attachmentmethods. STEP1 ) Select a location that is not prone to moisture and is located at least 36" away from combustible materials such as curtain drapes, furniture, bedding, paper, etc.
STEP 3) Have two people lift the fireplace machine up and insert the slots ( 2 slots on back of fireplace box) to the wall bracket hooks. STEP 4) With the fireplace installed safely, then using screws driver to lock the bracket and fireplace with two ST4x8 (D) screws in both sides.Check the appliance for stability ensuring that the appliance will not pull free from the wall.
IMPORTANT GLASS PANEL SAFETY INFORMATION! WARNING Under no circumstances should this product be operated with broken or chipped glass panels. Do not strike, slam or use blunt force on any part of the glass. Do not use abrasive cleansers to clean the glass. This product uses tempered glass. Replacement of the glass supplied by the manufacturer should be done by a qualified professional. This next step involves GLASS! ALWAYS use extreme caution when handling glass.
NOTE: To place to decorative crystals, follow these steps. Have a capable adult help you. STEP 6A. While one person holds the glass panel, remove the two screws at the top edge of the fireplace with a Phillips (+) screwdriver. STEP 6B. Together, carefully remove the front glass panel and set it aside on a clean soft surface. STEP 6C. Arrange the decorative crystals (F) on the shelf in the desired position. STEP 6D. Set the front glass panel back onto the firebox. STEP 6E.
Operation Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death. Power Plug the power cord into a 120 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.
Remote Control &Control Panel Operation (Control panel POWER switch must be ON to use remote control.) BUTTON FUNCTION ON: Enables control panel functions and remote control. Turns on flame effect. OFF: Disables control panel functions and POWER remote control. Turns off flame effect. TIMER button: Controls timer settings to turn off fireplace at selected time. TIMER NOTE: Flame effect stays on until power button is turned off. Flame effect must be on for heater to turn on.
Temperature Limiting Control This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, the heater will automatically turn OFF. To reset: 1. Unplug the power cord from the outlet. 2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes. 3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are, use a vacuum to clean the vent areas. 4.
ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. Electrical and Moving Parts: The fan motors are lubricated at the factory and will not require lubrication. Electrical components are integrated in the fireplace and are not serviceable by the consumer. Storage: Store heater in a clean dry place when not in use.
Troubleshooting ! WARNING DISCONNECT THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. Problem Possible Cause Solution 1. Fireplace turns off 1. Fireplace has overheated 1. Reset switch by turning and safety device has main power switch off caused thermal switch to and waiting 10 minutes disconnect or home circuit then turning it back on. breaker has opened. 2. Reset circuit breaker. 1.
7. Heater does not provide heat when turned on. 1. Thermal switch has been tripped. 2. Wiring is loose. 3. Heater is defective. 1. Turn unit off and unplug unit for 10 minutes. Plug back in and turn unit on. If plug cannot be reached, follow directions for tripped circuit breaker. 2. Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary. 3. Replace heater.
