Installation & Assembly

ManualsBrandsWade Logan ManualsCeiling LightsChifdale 3 - Light Unique / Statement Geometric LED Chandelier

•

Installation Guide

Lighting

Tools You May Need

GOGGLES

TAPE MEASURE

RUBBER

GLOVES

PHILLIPS

LADDER

DRILL

SCREW DRIVER

Parts List

H. Mounting Clips x

Circuit Box

Canopy Cover

Anchor Screws x 4

Outlet Screws x 3

Wire Connectors x 3

Ground Screw x 1

Canopy Cover Screws x 3

Plastic Anchors x 4

highly recommends to use a qualified, licensed electrician to install the

fixture.

LED INFO & WARNINGS

•

Please read and comprehend the entire manual before attempting to

assemble, operate, or install the product.

All parts must be used as indicated in these instructions. Do not substitute

any parts, leave parts out, or use any parts that are worn or broken.

Inspect the LED fixture prior to installation to make sure that it has not

been damaged during shipping.

Please handle the LED light with care when unpacking. Do not apply

pressure to the LEDʼs, do not open any factory sealed compartments, and

do not touch the LEDs with your hands.

•

Place the wall switch in the “OFF” position of the room you are installing

the fixture.

•

We recommends to install the fixture on its own independent circuit. Do

not install the fixture on the same circuit with other appliances, or HVAC

systems.

DO NOT CUT WIRES attached to the fixture under any circumstance.

Cutting wires will VOID

your warranty. Excess cable should be neatly

looped and tucked into the canopy.

Please remove the canopy from the box prior to the fixture body. Failure

to do so can potentially lead to cables getting tangled.

WE recommends Single Pole Switch only. (This fixture does not

support dimmer switches).

Shut “OFF” the electricity at main fuse box.

Summary of content (7 pages)

PAGE 1
Installation Guide LED INFO & WARNINGS • Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken. • Inspect the LED fixture prior to installation to make sure that it has not been damaged during shipping. • Please handle the LED light with care when unpacking.
PAGE 2
Fixture Diagram Outlet Box G Canopy cover screws A Canopy Cover E Wire Connector B Plastic Anchor F Ground Screw C Anchor Screw D Outlet Screw Ceiling
PAGE 3
Step 1. Adjust Height Locking Pin Cable The length of the cable is adjustable. To determine the proper length of the ﬁxture, hold the ﬁxture canopy up against the outlet box in the ceiling to adjust the cable. Depress locking pin on the canopy, hold pin in place, and pull down or push up on the cable. Repeat step for each cable. Installer Tip (1): It is recommended that two installers are required to adjust the height of the ﬁxture.
PAGE 4
Step 2. Install Canopy Cover Outlet Box Ceiling A Canopy Cover Raise canopy cover (A) to the ceiling. Mark location for the plastic anchors (B). Use drill to drill holes for plastic anchors (B). Insert plastic anchors (B) into hole. Outlet Box B Plastic Anchor Ceiling A Canopy Cover D Outlet Screw Attach canopy cover (A) to outlet box with outlet screws (D). Screw anchor screws (C) into plastic anchors (B) to secure canopy cover (A).
PAGE 5
Step 3. Secure Ring Frames Mounting H Clip Remove last two screws from mounting clip (H). Insert mounting clip (H) into slot on ring frame. Secure ring frame and mounting clip (H) with screws.
PAGE 6
Step 4. Connect Wires A Canopy Cover Black (Line Wire) White (Neutral Wire) F Ground Screw Wire E Connector Bare Copper (Ground Wire) Supply Wires: Connect Black (Line Wire) from ﬁxture to Black (Hot Wire) from outlet box. Connect White (Neutral Wire) from ﬁxture to White (Neutral Wire) from outlet box. Ground Wires: Connect Bare Copper (Ground Wire) from ﬁxture to Green or Bare Copper (Ground Wire) from outlet box. Twist wires together clockwise and secure with wire connector (E).
PAGE 7
Step 5.Mount Fixture Outlet Box G Canopy Screws A Canopy Cover Canopy Attach canopy to canopy cover (A). Twist canopy to lock ﬁxture in place. Secure canopy with canopy screws (G). Step 6. Turn Power ON Turn electricity “ON” at main fuse box. Place the single pole switch in the “ON” position to test the ﬁxture.