Installation & Assembly

Package Contents
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.ToolsRequired:
LightSource:
(3)MediumBaseBulbs100WMaximum.AlternateBulbs(3)23WCFL.
EstimatedAssembly Time:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Crossbar
x1
A
C
Ceiling Canopy
x1
D
2.5”L Spacer Tube
x1
Mounting Screw
x2
B
Shade Assembly
x1
Diffuser
x1
Rubber Washer
x2
F
E
G
H
Flat Washer
x2
I
Lock Ball
x1
J
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Inner Shade
x1
STEP 1 Install Ceiling Canopy to Shade
Assembly
-
A. Screw one end of the Spacer Tube (D) onto
the top center of the Shade Assembly (G) and
hand tighten until snug.
C
D
B. Thread the Ceiling Canopy (C)
onto the top end of the Spacer
Tube (D) and hand tighten until
snug.
Figure 1
STEP 2 Attach Crossbar to Outlet
Box
-
A. Attach the Crossbar (A) to Outlet Box
and secure by threading Outlet Box
Screws (not supplied) into the
Mounting Holes on the Outlet Box.
Tighten until snug.
A
Figure 2
Outlet
Box
Outlet Box
Screw
STEP 4 - Attach Ceiling Canopy to
Crossbar
A. Line up the holes on the side of the
Ceiling Canopy (C) to the mounting
holes on the Crossbar (A). Secure
them with Mounting Screws (B).
Tighten until sung.
A
B
C
Figure 4
STEP 5 - Install Inner Shade, Diffuser and Bulbs
A. Adjust the Hex Nut on the bottom end of the Nipple to proper
locations for rest components. Attach the Tabs on the bottom edge of
the Inner Shade (H) to the Diffuser (I).
C. Place Rubber Washers (E), Flat Washers (F), the Diffuser (I) with the
Inner Shade (H) over the end of the Nipple as shown. Secure them
Bulb
Tab
F
Figure 5
together by threading the Lock
Ball (J) onto the Nipple. Hand
tighten until snug.
C. This fixture uses standard bulb
with medium base. Maximum 100
watts. Insert bulb and screw
snugly into place.
Your fixture is now assembled and
ready to use. Enjoy!
J
G
E
H
E
F
I
Nipple