Installation & Assembly

ManualsBrandsWade Logan ManualsBathroom Vanity LightingAldrich 4-Light Dimmable Vanity light

1of2

STEP 1 - Attach Inner Backplate to

Outlet Box

A. Secure the Inner Backplate (A) to the

outlet box with outlet box screws (not

supplied). Tighten until snug.

* Pliers is required on this step.

Figure 1

Package Contents

Shade

Mounting Screw

Inner Backplate

STEP 2 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist

connectors until wires are tightly joined together. Wrap each

connection with approved electrical tape and carefully stuff all the

connected wires into the Outlet Box.

White wire

from fixture

Black wire

from fixture

Ground wire

from fixture

White wire

from supply

Black wire from

supply (or Red)

Ground wire

from supply

Fixture

Body

Socket

Collar Tool

Outlet Box

STEP 4 Install Shade-

A. Place Shades (F) over Sockets as shown. By

using the Socket Collar Tool (G), thread

Socket Collars (E) onto sockets to secure

Shades (F). Hand tighten until snug.

Figure 4

Figure 2

(4)LEDG94.5WBulbs,Maximum50WG9XenonFrostedBulbs

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

LightSource:

EstimatedAssemblyTime:

Preparation:

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Socket Collar

Outlet Box Screw

(not Supplied)

STEP 3 Install Fixture Body-

A. Place the backplate of the Fixture Body (C) onto the Inner Backplate

(A). Line up holes on the side of the backplate and the mounting

Figure 3

holes on the side of the Inner

Backplate (A). Secure them

together by threading

Mounting Screws (B) into the

mounting holes on the Inner

Backplate (A). Hand tighten

until snug.

STEP 5 Install Bulb

Note:

A. Install either the G9 Xenon bulb as specified (not provided) or install

the G9 LED bulbs (provided) if the fixture purchased is the LED

model.

This fixture is rated to use 50W maximum G9 Xenon bulbs.

You may use a lower wattage G9

Xenon or if you purchased the

LED model it is supplied with G9

LED bulbs.

Your fixture is now assembled

and ready to use. Enjoy!

Figure 5

Socket

LED G9 Bulb

Assembly Instruction

Summary of content (2 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) LED G9 4.5W Bulbs, Maximum 50W G9 Xenon Frosted Bulbs Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
CAUTION FOR BULB REPLACING When replacing bulbs, turn off power and allow lamp to cool. For safety purpose, wear gloves and eye protection. FINISH: POLISHED CHROME GN D FINISH: BRUSHED NICKEL 29” 6.25” 3.25” 6” 2 3” 3” NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" (4) 4.5W Maximum NO. PART NUMBER REPLACEMENT PART DESCRIPTION LED G9 Bulbs (Only provided BULB 4.5W LED G9 DIM WHITE 1 when the fixture is the LED model) SHADE 2 2of2 QTY. 4 4 5” 1 4.