52" or 42" CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz Please do not use any electric or battery powered tools in the assembly and installation of this or any this manufacturer's product.
TABLE OF CONTENTS Tools and Materials Required.........................................................................................1 Package Contents ......................................................................................................... 1 Safety Rules................................................................................................................... 2 Mounting Options........................................................................................................
1. TOOLS AND MATERIALS REQUIRED Philips screwdriver Blade screwdriver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: b a-1. Blade set (3) a-2. Blade set (5) b. Mounting bracket (preassembled with fan motor assembly) c. Fan motor assembly d. Fan housing e. Transmitter+holder+2 mounting screws f. 23A/12V battery g.
3. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 8. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 9.
4. MOUNTING OPTIONS If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes.
5. HANGING THE FAN Outlet box REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1. Disassemble the mounting bracket from the fan motor assembly. Washers Mounting bracket Step 2. Attach the mounting bracket to the outlet box using the two screws and washers provided with the outlet box. For best performance be sure the mounting bracket is level and secured firmly against the ceiling.
6. MAKE THE ELECTRIC CONNECTIONS Outlet box White ("AC IN N") Green or bare copper (ground) Black ("AC IN L") Remember to disconnect the power. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. Black (motor) Ground (green) (Connect to ground wire on hanger bracket if no house ground wire exists.) White (neutral) 1.
7. FINISHING THE INSTALLATION Safety cable Step 1. Move fan motor into position over the four mounting holes and secure with the four screws provided. (Fig. 7) Step 2. An additional safety support is provided to prevent the fan from falling. Secure the safety cable to the ceiling joist with screw and washer. (Fig. 7) Motor Screws Step 3. Raise the fan housing up against the mounting bracket. The four supports inside the fan housing should be placed against the four studs on the mounting bracket.
8. ATTACHING THE FAN BLADES 1. Fasten blade to motor using the screws supplied. (Fig. 9) 2. Repeat process with other blades. Tighten each screw and make sure the blade is straight. NOTE: This fan is supplied with two types of blades for installation. Follow the step below to installing your fan blade properly. Blade The inner holes are for 3 blades. The outer holes are for 5 blades.
9. PROGRAMMING YOUR FAN AND OPERATING THE REMOTE CONTROL Your DC brushless motor is equipped with a automatically learned type remote control. Install one 23A/12V battery (included). To prevent damage to transmitter, remove the battery if not used for long periods of time (Fig. 10) ON ECE 1 2 3 4 Restore power to ceiling fan and test for proper operation. A.
NOTE: During self calibration test, the remote is non-fuctional. NOTE: The learning frequency function and calibration test will continue to retain the last frequency and calibration set even when the power is shut off. If the frequency is changed self calibration test will occur again. self set AC the This receiver provides the following protective function: 1. Lock Rotor Position: The DC motor has a built-in safety against a stalled or locked rotor condition (stalled blade rotation).
11. CARE OF YOUR FAN Here are some suggestions to help you maintain your fan 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid scratching the finish.
LIMITED LIFETIME WARRANTY
