User Manual
EN
3
IMPORTANT SAFETY INFORMATION
WARNING - To reduce the risk of fire or
explosion:
• Do not spray ammable or combustible materials near an open
ame, pilot lights or sources of ignition such as hot objects,
cigarettes, motors, electrical equipment and electrical appliances.
Avoid creating sparks from connecting and disconnecting power
cords.
• For use with only water-based or mineral spirit-type materials
with a minimum ash point of 38ºC (100º F) — Do not spray or
clean with liquids having a ash point of less than 38ºC (100º
F). Flash point is the temperature at which a uid can produce
enough vapor to ignite.
• Verify that all containers and collection systems are grounded to
prevent static discharge.
• Connect to a grounded outlet and use grounded extension cords
(electric models only). Do not use a 3 to 2 adapter.
• Keep spray area well ventilated. Keep a good supply of fresh air
moving through the area to keep the air within the spray area free
from accumulation of ammable vapors.
• Do not smoke in the spray area.
• Do not operate light switches, engines, or similar spark producing
products in the spray area.
• Keep area clean and free of paint or solvent containers, rags, and
other ammable materials.
• Know the contents of the paint and solvents being sprayed.
Read all Material Safety Data Sheets (MSDS) and container labels
provided with the paints and solvents. Follow the paint and
solvent manufacture’s safety instructions.
• Fire extinguisher equipment shall be present and working.
WARNING - To reduce the risk of injury:
• Always wear appropriate gloves, eye protection, clothing and a
respirator or mask when painting. Hazardous vapors – Paints,
solvents, insecticides, and other materials can be harmful if
inhaled or come in contact with body. Vapors can cause severe
nausea, fainting or poisoning.
• Do not operate or spray near children. Keep children away from
equipment at all times.
• Do not overreach or stand on an unstable support. Keep eective
footing and balance at all times.
• Stay alert and watch what you are doing.
• Do not operate the unit when fatigued or under the inuence of
drugs or alcohol.
• Never aim spray gun at any part of the body.
• Follow all appropriate local, state, and national codes governing
ventilation, re prevention, and operation.
• The United States Government Safety Standards have been
adopted under the Occupational Safety and Health Act (OSHA).
These standards, particularly part 1910 of the General Standards
and part 1926 of the Construction Standards should be consulted.
• Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specications and safety devices of the turbine manufacturer.
• Power cord must be connected to a grounded circuit.
• Do not spray outdoors on windy days.
• Use only Wagner HVLP hose.
WARNING - To reduce the risk of electric shock:
• Do not submerge air hose into any liquids.
• Power cord must be connected to a grounded circuit.
• Never submerge electrical parts.
• Never expose the equipment to rain. Store indoors.
• Keep electrical cord plug and spray gun trigger free from paint
and other liquids. Never hold the cord at plug connections to
support the cord. Failure to observe may result in an electrical
shock.
THANK YOU FOR YOUR PURCHASE!
Designed with the Upcycling professional in mind, the Studio Pro™
helps you nish projects faster and with less paint waste. The air power
adjustments and paint ow settings provide control you won’t expect
and the nish you want for every piece. From chalk, milk and latex
paints to stains, urethanes and sealers, the Studio Pro was designed
to spray any coating to create the look you want. Get quality projects
done in less time with the Studio Pro Sprayer.
TABLE OF CONTENTS
IMPORTANT SAFETY INFORMATION ...........................................................2-3
OVERVIEW .................................................................................................................4
CONTROLS AND FUNCTIONS .............................................................................5
MATERIAL PREPARATION ....................................................................................6
ASSEMBLY .................................................................................................................7
POWER AND MATERIAL CONTROLS ................................................................8
SPRAY PATTERN ADJUSTMENT .........................................................................9
PROPER SPRAYING TECHNIQUE ...............................................................10-11
CLEANUP ..........................................................................................................12-13
REASSEMBLY ..........................................................................................................14
MAINTENANCE ......................................................................................................15
TROUBLESHOOTING ............................................................................................16
PARTS LIST .......................................................................................................49-51
WARRANTY .............................................................................................................54